CITB Heating and Plumbing Services: Gas safety, combustion and flues practice questions

Written by Acacio Oliveira, founder of FreeMocks, plumbing and heating engineer (F-Gas registered).

40 of our 200 CITB HS&E Specialist Test: Heating and Plumbing Services (CITB-SPEC-HAPS) questions are on gas safety, combustion and flues, about 20% of the bank. Try 6 below with full worked answers, then practise the rest in a timed mock.

Practice questions

Pick an answer to see why it's right, why the others are wrong, and the page in the book.

Q1. Where must an LPG storage tank not be located?

Show answer

Answer: D. Indoors, in a bunded area or on a roof

  • LPG tanks should not be located indoors, within a bunded area or on a roof.
  • Sites should allow safe access for road tankers.

UKLPG Codes of Practice give more detail.

Why the others are wrong:

A: outdoor level ground is a normal location.

B: tanker access should be planned for.

C: this is not one of the listed exclusions.

Memory trick:

LPG tank: not in, not bunded, not up top.

Find it in the book

HSE L56 (5th edition, 2018), page 29

Reg HSE L56 (5th edition, 2018), guidance para 127

Q2. A mechanical services firm wants its engineers to replace gas boilers in a school. What must the firm be?

Show answer

Answer: C. A member of an HSE-approved class, such as Gas Safe

  • No employer may let employees work on gas fittings unless the employer is a member of a class of persons approved by HSE.
  • At present this means Gas Safe Register.

Each engineer must also be competent for the work.

Why the others are wrong:

A: trade association membership is not the legal test.

B: insurance does not meet the registration duty.

D: building control does not approve gas businesses.

Memory trick:

Business on the register, engineer competent.

Find it in the book

HSE L56 (5th edition, 2018), page 23

Reg HSE L56 (5th edition, 2018), regulation 3(3) and guidance para 91

Q3. You find a dangerous gas appliance and the owner refuses to let you disconnect it. What should you do?

Show answer

Answer: B. Tell them in writing, label it and, if agreed, shut it off

  • Inform the user and owner in writing that the appliance is unsafe and continued use is an offence.
  • The engineer has no legal power to disconnect without consent; label it and, with agreement, close the shut-off.

For natural gas, the engineer can then call 0800 111 999.

Why the others are wrong:

A: engineers have no legal power to disconnect without consent.

C: the user must be told in writing and the appliance labelled.

D: removing the meter is not the engineer's role here.

Memory trick:

Write it, tag it, shut it if allowed.

Find it in the book

HSE L56 (5th edition, 2018), page 64

Reg HSE L56 (5th edition, 2018), guidance paras 286 and 287

Q4. You are moving a gas catering appliance to another position in the same kitchen. What does regulation 26(3) require?

Show answer

Answer: C. Check it is safe for further use before refitting

  • No person shall install a used appliance without checking it is safe for further use.
  • This also applies when an appliance is moved, even within the same room.

Inspection may not be possible once installed.

Why the others are wrong:

A: the rule also applies to appliances moved within the same room.

B: a new badge is not required.

D: the check is of the appliance's condition.

Memory trick:

Moved counts as used.

Find it in the book

HSE L56 (5th edition, 2018), page 54

Reg HSE L56 (5th edition, 2018), regulation 26(3) and guidance para 234

Q5. A kitchen refit adds a powerful extract fan in a room with an open-flued gas boiler. What is the risk?

Show answer

Answer: A. The fan could pull flue products back into the room

  • Fitting extractor fans can overcome the pull on flues so flue products are sucked back into the premises.
  • Alterations to premises must not make existing gas fittings unsafe.

Safety implications must be addressed before the work.

Why the others are wrong:

B: condensation is not the safety concern raised.

C: extract fans do not change the gas pressure.

D: servicing access is not affected.

Memory trick:

Strong fan, spilling flue.

Find it in the book

HSE L56 (5th edition, 2018), page 32

Reg HSE L56 (5th edition, 2018), guidance para 144

Q6. A Gas Safe engineer finds a fitting so dangerous it needs disconnecting. What else is usually required?

Show answer

Answer: C. A report to HSE under RIDDOR

  • RIDDOR requires Gas Safe engineers to report gas fittings dangerous enough that people could die, lose consciousness or need hospital treatment.
  • A report will generally be required where disconnection is necessary.

Reports can be made online.

Why the others are wrong:

A: the legal report is to HSE.

B: the report goes to HSE under RIDDOR.

D: RIDDOR requires a report of certain dangerous fittings.

Memory trick:

Disconnected as dangerous? RIDDOR it.

Find it in the book

HSE L56 (5th edition, 2018), page 64

Reg HSE L56 (5th edition, 2018), guidance para 290; HSE INDG453 (rev1, 2013), reportable gas incidents

Want 194 more CITB Heating and Plumbing Services questions? Start a free timed mock.

Start a free mock

Full mock, no card needed. Full workouts on the first 5 questions.

Other CITB Heating and Plumbing Services topics

Free official guides for this topic

Our questions are written from these documents. Download them free to revise from the source.

© Crown copyright (HSE, GOV.UK). Unchanged copies, reproduced under the Open Government Licence v3.0. FreeMocks is not connected to or endorsed by HSE or the government.

Revise this topic