AM2S v1 Knowledge Test: Fault diagnosis and rectification practice questions

Written by Acacio Oliveira, founder of FreeMocks, plumbing and heating engineer (F-Gas registered).

20 of our 180 AM2S v1 Knowledge Test (Section E) (AM2S-V1) questions are on fault diagnosis and rectification, about 11% of the bank. Try 6 below with full worked answers, then practise the rest in a timed mock.

Practice questions

Pick an answer to see why it's right, why the others are wrong, and the page in the book.

Q1. Every time you take a loop impedance reading on an RCBO-protected circuit, the RCBO trips. What does GN3 suggest?

Show answer

Answer: A. Use a non-trip tester (under about 15 mA) or DC biasing

  • GN3: the test current of EFLI testers may trip RCDs, preventing a measurement.
  • Testers less likely to trip RCDs limit the test current to less than 15 mA or use DC biasing, which saturates the RCD core first.
  • Alternatively, Zs can be found from Ze + (R1 + R2).

Non-trip readings take longer and vary more, so repeat them.

Why the others are wrong:

B: a trip prevents a reading; it doesn't verify Zs.

C: bypassing protective devices is unsafe; GN3 points to suitable non-trip testers.

D: an insulation test doesn't measure earth fault loop impedance.

Memory trick:

RCD keeps tripping? Go low current or DC bias.

Find it in the book

IET Guidance Note 3 (2022 edition), page 87

Reg GN3, 2.6.15, Circuit-breakers and RCDs

Q2. After a neighbour's supply problem, a customer's lights burn very bright and two appliances fail. You suspect an open-circuit PEN in the supply cable. What can the line to neutral voltage rise to?

Show answer

Answer: A. About 400 V

  • GN3 Appendix D Note 1: if there is an open-circuit PEN conductor, the line to neutral voltage may rise to 400 V nominal.
  • Diverted neutral currents can also cause hazardous touch voltages on earthed metalwork.

Report a suspected open PEN to the DNO on 105 straight away.

Why the others are wrong:

B: the voltage rises on a lightly loaded phase, it doesn't fall to 110 V.

C: an open PEN can push the line-neutral voltage far beyond the normal tolerance.

D: a broken PEN loses that reference for the installation, so the voltage can rise.

Memory trick:

Lost PEN: up to 400 V across your kit.

Find it in the book

IET Guidance Note 3 (2022 edition), page 187

Reg GN3, Appendix D, Note 1

Q3. A 30 mA RCD has 18 mA of standing leakage on it. A customer says it can't be the cause of nuisance trips, since 18 mA is less than 30 mA. Why are they wrong?

Show answer

Answer: C. RCDs may trip above 50 % of rating, here 15 mA

  • 531.3.2 NOTE 2: RCDs may operate at any value of residual current in excess of 50 % of the rated residual current.
  • 50 % of 30 mA is 15 mA, so 18 mA of standing leakage can cause unwanted tripping.
  • Design aim: keep accumulated leakage to 30 % (9 mA).

A small extra leakage, such as a kettle element, may then tip it over.

Why the others are wrong:

A: NOTE 2 says an RCD may operate at any value above 50 % of IΔn.

B: leakage isn't an overload; the issue is residual current near the trip range.

D: BS 7671 says they may operate above 50 %, not that they always trip at it.

The maths

50 % × 30 mA = 15 mA
18 mA > 15 mA, so tripping is possible

Memory trick:

Over half the rating, it may go.

Find it in the book

BS 7671:2018+A4:2026, page 165

Reg BS 7671:2018+A4:2026, 531.3.2 NOTE 2

Q4. An office RCD trips randomly. Each circuit on it passes insulation tests, but with all the PCs running, the earth leakage clamp reads 14 mA on the 30 mA RCD. What is the best long-term fix?

Show answer

Answer: B. Spread the circuits over more RCDs or RCBOs

  • 531.3.2: to limit unwanted tripping, consider subdividing circuits with individual RCDs and using RCBOs.
  • The accumulated protective conductor and leakage currents downstream of an RCD should be not more than 30 % of IΔn: here 9 mA.
  • 14 mA is well over 9 mA, so the RCD is close to its trip range.

RCDs may trip at any residual current over 50 % of their rating.

Why the others are wrong:

A: an SPD deals with transient overvoltages; it does nothing about standing leakage current.

C: removing earths is dangerous and would not be a fix.

D: sockets up to 32 A need 30 mA additional protection; the fix is to subdivide.

The maths

Limit = 0.30 × 30 mA = 9 mA
Measured 14 mA > 9 mA

Memory trick:

Too much leakage on one RCD? Share it out.

Find it in the book

BS 7671:2018+A4:2026, page 165

Reg BS 7671:2018+A4:2026, 531.3.2(a) and (c)

Q5. Step 1 on a new ring gives r1 = 0.52 Ω and rn = 0.52 Ω, but the cpc end-to-end reads open circuit. What does this point to?

Show answer

Answer: C. A break or bad termination in the ring's cpc

  • GN3 step 1: an open circuit or a reading above the continuity range shows a damaged conductor or a problem with the integrity of connections or terminations in that conductor.
  • With 2.5 mm²/1.5 mm² cable, a healthy r2 would be about 1.67 × 0.52 ≈ 0.87 Ω.

Check the earth terminations at each socket, starting where work was last done.

Why the others are wrong:

A: a smaller cpc reads about 1.67 times r1, not open circuit.

B: the line and neutral loops read normally; the open circuit is on the cpc.

D: a spur shows up as a higher step 2 or step 3 reading, not an open cpc loop.

Memory trick:

Open on r2? The earth loop is broken.

Find it in the book

IET Guidance Note 3 (2022 edition), page 62

Reg GN3, 2.6.6 Step 1

Q6. A ring's step 1 readings are r1 = 0.95 Ω, rn = 0.62 Ω, with the cable length suggesting about 0.60 Ω for each. What is the likely problem?

Show answer

Answer: A. A poor line termination somewhere on the ring

  • GN3: r1 and rn should be of the same order if the conductors are the same length, csa and material.
  • Readings higher than expected suggest a problem with the integrity of one or more conductor terminations.

Check each line terminal, including at the consumer unit.

Why the others are wrong:

B: GN3 says readings should be of the same order where conductors are the same length, csa and material.

C: spurs don't change the end-to-end loop readings of step 1.

D: a figure of eight gives lower readings than expected, not higher.

Memory trick:

One loop high? Hunt the loose line terminal.

Find it in the book

IET Guidance Note 3 (2022 edition), pages 62 to 63

Reg GN3, 2.6.6 Step 1

Want 174 more AM2S v1 Knowledge Test questions? Start a free timed mock.

Start a free mock

Full mock, no card needed. Full workouts on the first 5 questions.

Other AM2S v1 Knowledge Test topics

Revise this topic