Work at Height Regulations 2005: what every site worker needs to know
Updated 2 November 2026. Written by Acacio Oliveira, founder of FreeMocks, plumbing and heating engineer (F-Gas registered).
Falls from height are one of the biggest causes of death and serious injury at work. The Work at Height Regulations 2005 set a simple order: avoid working at height if you reasonably can, prevent falls if you can't avoid it, and minimise the distance and consequences of a fall where the risk remains. Protection for everyone (like guard rails) comes before protection for one person (like a harness). Working platforms you could fall more than 2 metres from must be inspected after they're put up, after anything that could affect them, and at least every seven days. This guide is based on HSE's free leaflet INDG401 and comes up in the CITB HS&E test for the CSCS card.
What counts as work at height
Work at height is work anywhere a person could fall far enough to be hurt if there were no precautions. Working on a ladder or a flat roof counts, and so does working near a fragile surface you could fall through, or near an opening in a floor or a hole in the ground.
Avoid, prevent, minimise
Before any work at height, work through these steps in order:
- Avoid: do as much as possible from the ground, for example with extendable tools, or by assembling edge protection at ground level.
- Prevent: use a place that's already safe, such as a roof with permanent guard rails, or equipment that stops falls, such as scaffolds, tower scaffolds and MEWPs.
- Minimise: if a fall is still possible, reduce the distance and the harm, for example with safety nets, air bags or a fall-arrest harness on a high anchor point.
Collective before personal protection
Collective protection protects everyone and doesn't need the worker to do anything for it to work, for example a guard rail. Personal protection only works if the person uses it correctly, for example clipping a harness lanyard to a suitable anchor. Always consider collective protection first. On a fully boarded and guarded scaffold that isn't being altered, workers don't also need a harness.
Fragile roofs
Falls through fragile roofs and roof lights are among the most common causes of death at work. Treat these as likely to be fragile:
- Roof lights
- Liner panels on built-up sheeted roofs
- Non-reinforced fibre cement sheets
- Corroded metal sheets
- Glass, including wired glass
- Rotted chipboard
- Slates and tiles
Inspections
Equipment whose safety depends on how it's put up, such as a scaffold, must not be used until a competent person has inspected it in position. A working platform used for construction work, where someone could fall more than 2 metres, must be inspected:
- after it's assembled in any position
- after any event likely to have affected its stability, such as bad weather or accidental damage
- at intervals of no more than seven days
Ladders and your own duties
Ladders aren't banned. For low-risk, short tasks (under 30 minutes) a ladder can be the sensible choice, as long as the person has been shown how to use it safely. As a worker, you must report any hazard you spot, use the equipment and safety devices provided properly, and follow the training and instructions you've been given.
Official sources
Practise for it
Test yourself with a free timed mock, with every answer explained.
Start a free mockFrequently asked questions
What is the order of control for work at height?
Avoid work at height where you reasonably can; if you can't, prevent falls with a safe place of work or the right equipment; and where a fall is still possible, minimise the distance and consequences. Collective protection comes before personal protection at each step.
How often must a scaffold be inspected?
A working platform for construction work, where someone could fall more than 2 metres, must be inspected after assembly, after any event that could affect its stability, and at intervals of no more than seven days.
Are ladders banned on building sites?
No. HSE says ladders and stepladders are not banned. For low-risk, short-duration work (under 30 minutes) they can be the most suitable equipment.
Is this in the CITB HS&E test?
Yes. Working at height is one of the high-risk activities covered in the CITB Health, Safety and Environment test for the CSCS card.
Related
RIDDOR: what must be reported · Legionella water temperatures · Safe isolation procedure · CITB HS&E mock test sites compared · EV charger installation regulations: what Section 722 requires · Part P notifiable work: which electrical jobs need notifying · Unvented discharge pipes: tundish, D1 and D2 rules explained
Sources: HSE INDG401: Working at height, a brief guide (rev2). This guide paraphrases the rules for revision; always work from the current official documents.
