WRAS Water Regs: Testing, flushing and maintenance practice questions

Written by Acacio Oliveira, founder of FreeMocks, plumbing and heating engineer (F-Gas registered).

9 of our 60 Water Regulations (WRAS) (WRAS-WATER-REGS) questions are on testing, flushing and maintenance, about 15% of the bank. Try 6 below with full worked answers, then practise the rest in a timed mock.

Practice questions

Pick an answer to see why it's right, why the others are wrong, and the page in the book.

Q1. A PEX system is tested using Test B at 9 bar. After 30 minutes of pumping the gauge is noted at 9.0 bar. Thirty minutes after that it reads 8.6 bar, and 150 minutes after the noted reading it reads 8.3 bar. No leaks are seen. What is the result?

Show answer

Answer: B. Pass, as both pressure drops are within the limits

  • Sch 2 para 12(2)(b) Test B: after 30 minutes pumping, note the pressure; the drop must be less than 0.6 bar after the next 30 minutes, or 0.8 bar after the next 150 minutes, with no visible leakage.
  • 9.0 to 8.6 = 0.4 bar (under 0.6). 9.0 to 8.3 = 0.7 bar (under 0.8).

Both readings are inside the limits, so the system passes.

Why the others are wrong:

A: Test B allows a small drop; it does not require the pressure to hold exactly.

C: 0.5 bar is not a Test B limit; the limits are 0.6 and 0.8 bar.

D: 0.6 bar is the 30 minute limit; after 150 minutes the limit is 0.8 bar.

The maths

Noted pressure = 9.0 bar
Drop after 30 min = 9.0 - 8.6 = 0.4 bar (limit 0.6): OK
Drop after 150 min = 9.0 - 8.3 = 0.7 bar (limit 0.8): OK
No visible leakage: PASS

Memory trick:

Test B: 0.6 at half an hour, 0.8 at two and a half.

Reg Water Fittings Regs Sch 2 para 12(2)(b) Test B

Q2. A new installation is entirely copper with no plastic pipe. After raising it to test pressure by pumping, how long must the test continue without further pumping?

Show answer

Answer: D. 1 hour, with pressure held and no visible leaks

  • Sch 2 para 12(2)(a): for a system with no plastic pipe, pump to test pressure, then continue one hour without further pumping.
  • Pressure must be maintained for one hour with no visible leakage.

Plastics creep under pressure, so they get the separate Test A and Test B.

Why the others are wrong:

A: that is part of Test B for systems that include plastic pipe.

B: 30 minutes is the pumping period in the tests for systems containing plastics.

C: that is part of Test A for systems that include plastic pipe.

Memory trick:

All metal: one hour, no drop, no drip.

Reg Water Fittings Regs Sch 2 para 12(2)(a)

Q3. Which of these flushing cisterns is NOT required to have a warning pipe or an equally effective device?

Show answer

Answer: D. An automatic urinal flushing cistern

  • Sch 2 para 25(1)(h): every flushing cistern must have a warning pipe or no less effective device, except a pressure flushing cistern or a urinal cistern.
  • Most modern WC cisterns use an internal overflow into the pan as the equally effective device.

An automatic urinal cistern discharges by design, so it is excluded.

Why the others are wrong:

A: being concealed does not exempt it; an internal overflow is the usual solution.

B: WC flushing cisterns must have a warning pipe or equally effective device.

C: dual flush WC cisterns are still covered by the requirement.

Memory trick:

Every WC cistern needs a warning; urinals and pressure cisterns don't.

Reg Water Fittings Regs Sch 2 para 25(1)(h)

Q4. A system with plastic pipework has a maximum design pressure of 8 bar and is tested using Test A. After 30 minutes at test pressure, what happens next?

Show answer

Answer: A. Reduce to 4 bar; it must not fall below 4 bar over 90 minutes

  • Test pressure = 1.5 x 8 = 12 bar, pumped for 30 minutes.
  • Sch 2 para 12(2)(b) Test A: reduce to one third of the test pressure (12 / 3 = 4 bar), and it must not drop below that over the next 90 minutes, with no visible leakage.

Dropping the pressure lets the plastic contract, so a sound system holds or slightly rises.

Why the others are wrong:

B: this uses the design pressure; Test A reduces to one third of the test pressure.

C: this halves the test pressure instead of taking one third.

D: that mixes in the Test B criterion.

The maths

Design pressure = 8 bar
Test pressure = 1.5 x 8 = 12 bar
After 30 min pumping, reduce to 12 / 3 = 4 bar
Pass if it stays at or above 4 bar for 90 min with no visible leaks

Memory trick:

Test A: pump 30, drop to a third, hold for 90.

Reg Water Fittings Regs Sch 2 para 12(2)(b) Test A

Q5. During a service visit on an unvented cylinder, you check where the T&P and expansion valve discharges end up. What does Schedule 2 require of those discharges?

Show answer

Answer: B. They must be made in a safe and conspicuous manner

  • Sch 2 para 19: discharges from temperature relief valves, T&P valves and expansion valves must be made in a safe and conspicuous manner.
  • Para 22(1): each of these valves must close automatically after discharging.

A visible discharge warns that something has gone wrong; a hidden one can go unnoticed for months.

Why the others are wrong:

A: discharging hot water into a storage cistern would contaminate it.

C: the discharge must be conspicuous so a fault gets noticed.

D: no particular appliance is specified; the test is safe and conspicuous.

Memory trick:

Safety valve water must be seen and must not scald.

Reg Water Fittings Regs Sch 2 paras 19 and 22(1)

Q6. A refurbishment uses copper for the risers and PEX for the flat distribution. Which pressure test route is deemed to satisfy the Regulations?

Show answer

Answer: B. Either Test A or Test B for systems that include plastics

  • Sch 2 para 12(2)(a): the one hour test is for a system that does not include a pipe made of plastics.
  • Para 12(2)(b): in any other case, either Test A or Test B must be satisfied.

One length of plastic pipe puts the whole system into the plastics tests.

Why the others are wrong:

A: the metal-only test applies only where the system has no plastic pipe at all.

C: the test applies to the whole system, and the one hour test is for metal systems.

D: the Regulations require the system to withstand the test pressure.

Memory trick:

Any plastic at all: pick A or B.

Reg Water Fittings Regs Sch 2 para 12(2)

Want 54 more WRAS Water Regs questions? Start a free timed mock.

Start a free mock

Full mock, no card needed. Full workouts on the first 5 questions.

Other WRAS Water Regs topics

Revise this topic