Fluid categories 1 to 5 in the Water Regulations
Updated 30 October 2026. Written by Acacio Oliveira, founder of FreeMocks, plumbing and heating engineer (F-Gas registered).
The Water Supply (Water Fittings) Regulations 1999 sort every fluid in a plumbing system into five categories by how much harm it would do if it flowed back into the mains. Category 1 is wholesome drinking water and category 5 is a serious health hazard such as human waste from a WC. The higher the category at a fitting, the stronger the backflow protection it needs, from a single check valve for category 2 up to an air gap or a type of device rated for category 5.
Where the fluid categories come from
Schedule 1 of the Water Supply (Water Fittings) Regulations 1999 defines the five categories. Schedule 2 paragraph 15 then requires every water system to have adequate devices for preventing backflow, appropriate to the highest fluid category the fitting is subject to downstream, before the next such device. In Scotland the Water Supply (Water Fittings) (Scotland) Byelaws 2014 apply instead.
Schedule 1 gives only short definitions and a few examples. The everyday examples below come from water industry guidance, mainly the water companies' fact sheets and WaterRegsUK. The final decision on a category rests with the local water supplier.
The five categories
Each definition below is a paraphrase of Schedule 1. The examples are ones listed in water supplier guidance for homes and small commercial jobs.
| Category | What it means | Typical examples |
|---|---|---|
| 1 | Wholesome water supplied by a water undertaker that meets the drinking water quality regulations | Cold water straight from the main |
| 2 | Category 1 water whose aesthetic quality is impaired by a change in temperature, taste, odour or appearance | Hot water, mixing hot and cold supplies, a domestic softener regenerated with common salt, ice makers |
| 3 | Slight health hazard from substances of low toxicity, such as ethylene glycol, copper sulphate or similar additives, or common disinfectants | Water in domestic heating systems, domestic washing machines and dishwashers, hand basins, baths and showers |
| 4 | Significant health hazard from toxic substances, including chemicals, carcinogens, pesticides and environmental organisms | Commercial heating systems, commercial dishwashing and clothes washing, printing and photographic equipment, dairies |
| 5 | Serious health hazard from pathogens, radioactive or very toxic substances, including human or animal waste | WC pans, urinals, bidets, sinks, grey water recycling systems, permeable pipes at or below ground, laboratories, non-domestic hose union taps, livestock fields and abattoirs |
Matching the backflow device to the category
Backflow can happen in two ways. Back pressure is when downstream pressure is higher than the supply, for example from a pump or thermal expansion. Back siphonage is when the supply pressure drops and fluid is sucked back, for example after a burst main. The Regulator's Specification rates each arrangement or device against both. Some, such as the AUK2 and AUK3 tap gaps and the DC pipe interrupter, are rated for back siphonage only, which is why the device table is worth checking for each installation.
The general rule, in plain terms, is set out below.
| Highest fluid category | Typical protection | Device type code |
|---|---|---|
| 2 | Single check valve | EA (verifiable) or EB (non-verifiable) |
| 3 | Double check valve | EC (verifiable) or ED (non-verifiable) |
| 4 | Reduced pressure zone (RPZ) valve | BA |
| 5 | Air gap, for example a Type AA unrestricted air gap or a category 5 break cistern | AA, AB and AD for both back pressure and back siphonage. AUK1, AUK3 and DC are rated for category 5 back siphonage only |
Domestic examples you will meet
Most backflow questions in a domestic setting come down to a handful of fittings. Learn these and you will handle most exam questions.
- Filling loop on a sealed heating system: category 3. A temporary filling hose needs a double check valve at the supply connection and must be removed once filling is finished. A permanent connection needs a Type CA device or equivalent
- Washing machine or dishwasher in a house: category 3. WRAS-approved appliances should have backflow protection built in, but some water suppliers also ask for a double check valve on the feed
- Outside tap in a house garden: category 3. On new installations a double check valve and service valve go inside the building. Hose union taps on non-domestic premises are category 5
- Bath and basin taps in a house: category 3. A Type AUK2 tap gap above the spill-over level normally covers this, or a double check valve where the gap cannot be kept
- Kitchen sink taps: sinks are listed under category 5, so the tap outlet needs a Type AUK3 gap of at least 20 mm or twice the inlet bore, whichever is greater
- WC cistern: category 5 risk from the pan. The float valve needs a Type AUK1 arrangement with an air gap above the overflow
- Shower hose that can reach into the bath: use double check valves, a retaining ring or a shorter hose so the head cannot drop into the water. The hose must never reach a WC
Why the category is set by the worst case
Schedule 2 paragraph 15(3) says the device must suit the highest fluid category the fitting is subject to downstream, up to the next backflow device. So you protect against what could reasonably end up downstream, not just what is there today. That is why the same hose union tap is treated as category 3 in a house garden but category 5 on non-domestic premises.
Notification and approved fittings
Regulation 4 requires water fittings to be of an appropriate quality and standard, for example by conforming to a British Standard or to a specification approved by the regulator. Product approval schemes such as WRAS Approval are the usual way to show this. Regulation 5 lists work that must be notified to the water undertaker, with its consent obtained, before it starts. The list includes installing an RPZ valve or other mechanical device against category 4 or 5 fluids, a garden watering system unless it is designed to be operated by hand, a bath over 230 litres, and new buildings. Approved contractors are exempt from notifying some items. The water undertaker enforces the regulations (regulation 10) and its authorised staff can inspect installations (regulation 9).
Official sources
- Water Supply (Water Fittings) Regulations 1999, Schedules 1 and 2 (legislation.gov.uk)
- Water Supply (Water Fittings) Regulations 1999, regulations 1 to 14 (legislation.gov.uk)
- WaterRegsUK: Regulator's Specification for backflow prevention arrangements
- WaterRegsUK: Backflow protection and fluid categories
- SES Water: Contamination and protection of water supplies fact sheet
- SES Water: Plumbing in domestic properties fact sheet
Practise for it
Test yourself with a free timed mock, with every answer explained.
Start a free mockFrequently asked questions
What are the five fluid categories?
Category 1 is wholesome mains water. Category 2 is water changed in taste, smell, look or temperature, such as hot water. Category 3 is a slight health hazard from low-toxicity substances, category 4 a significant health hazard from toxic substances, and category 5 a serious health hazard from pathogens, radioactive or very toxic substances.
What fluid category is a domestic central heating system?
Category 3 in water supplier guidance. Schedule 1 lists chemical additives such as ethylene glycol under category 3, so inhibitor does not move it up. A commercial heating system is category 4. That is why a domestic filling loop needs a double check valve and a temporary hose must be removed after use.
What fluid category is a WC?
Category 5, because the pan can contain human waste. The cistern float valve is protected by a Type AUK1 arrangement with an air gap above the overflow.
What backflow device protects against category 4?
A reduced pressure zone valve (type BA) is the usual mechanical device for category 4. Installing an RPZ valve is notifiable work under regulation 5, so the water supplier must be told before it is fitted.
Is there a water regulations exam?
Yes. Water regulations courses from training providers end in an assessment on the regulations and the backflow rules. You can practise with our free water regulations mock.
Related
Sources: Water Supply (Water Fittings) Regulations 1999, Schedules 1 and 2 (legislation.gov.uk); Water Supply (Water Fittings) Regulations 1999, regulations 1 to 14 (legislation.gov.uk); WaterRegsUK: Regulator's Specification for backflow prevention arrangements; WaterRegsUK: Backflow protection and fluid categories; SES Water: Contamination and protection of water supplies fact sheet; SES Water: Plumbing in domestic properties fact sheet. This guide paraphrases the rules for revision; always work from the current official documents.
