QELTK3/006: Legislation, requirements and certification practice questions

Written by Acacio Oliveira, founder of FreeMocks, plumbing and heating engineer (F-Gas registered).

43 of our 180 Inspection, Testing, Commissioning and Certification (QELTK3-006) questions are on legislation, requirements and certification, about 24% of the bank. Try 6 below with full worked answers, then practise the rest in a timed mock.

Regulations that come up most

The regulation groups our legislation, requirements and certification questions test most often. Know where these are in your book before the exam.

  • 644.4 · 3 questions
  • 132.16 · 2 questions
  • 514.9 · 1 questions
  • 644.1 · 1 questions
  • 653.1 · 1 questions
  • 653.2 · 1 questions
  • 653.4 · 1 questions
  • 653.5 · 1 questions

Practice questions

Pick an answer to see why it's right, why the others are wrong, and the page in the book.

Q1. Before initial verification, which item of information is NOT normally required to be made available to the inspector?

Show answer

Answer: D. The manufacturer's name for each cable used

  • The inspector needs diagrams, charts or tables, plus maximum demand, number and type of conductors, earthing system, nominal voltage, frequency, prospective short-circuit current, Ze and type and rating of protective devices.
  • Cable manufacturer names are not on the list.

The information lets the inspector compare the installation with the design.

Why the others are wrong:

A: this is listed general information.

B: this is listed general information.

C: this is listed general information.

Memory trick:

Know the supply, the earthing and the protection before you start.

Find it in the book

Linsley, Electrical Installation Work Level 3 (EAL Edition), page 273

Reg 514.9; GN3

Q2. What does the book recommend before shutting down emergency lighting or standby supply circuits for testing?

Show answer

Answer: C. Obtain verbal or written authorisation

  • Obtain verbal or written authorisation to shut down emergency operation or standby circuits.
  • Also fix warning notices, screen off the area with cones and tape, and tell everyone testing is about to start.

Emergency systems protect occupants, so someone in charge must agree to them being off.

Why the others are wrong:

A: the authorisation needed is from those responsible for the building.

B: this is not the stated requirement.

D: this is not listed as a requirement.

Memory trick:

Emergency off needs an OK.

Find it in the book

Linsley, Electrical Installation Work Level 3 (EAL Edition), page 270

Reg EAL Ch4 safe working

Q3. A sole trader designs, installs and tests a full rewire of a bungalow. How can the signature part of the EIC be completed?

Show answer

Answer: B. A single-signature declaration may replace the three boxes

  • Where design, construction, inspection and testing are all the responsibility of one person, a certificate with a single-signature declaration may replace the multiple-signature section.
  • The model wording is given in the Introduction to Appendix 6.
  • On a multiple-signature form, a person responsible for more than one part signs in each place.

One person, one declaration covering all three responsibilities.

Why the others are wrong:

A: BS 7671 allows one person to be responsible for all three parts of the work.

C: the client is not the designer and does not sign the certificate.

D: design and construction must also be certified; a single declaration covers all three.

Memory trick:

Did it all yourself? One signature, three jobs.

Find it in the book

BS 7671:2018+A4:2026, page 536; IET Guidance Note 3 (2022 edition), page 23

Reg Appendix 6 Introduction

Q4. According to the book, why do most voltage-indicating test devices not have fuses fitted in their test leads?

Show answer

Answer: B. A fuse would add significant resistance to the leads

  • Most testers do not include a protective fuse because it would add significant resistance to the test leads.
  • Protection is still provided through electronic circuitry, and the leads must be well insulated and robust.

The absence of a fuse makes good probe and lead design even more important.

Why the others are wrong:

A: GS38 does not ban fused leads.

C: voltage indicators are used on mains voltage.

D: lead length is not the reason given.

Memory trick:

Fuse adds ohms, so electronics do the protecting.

Find it in the book

Linsley, Electrical Installation Work Level 3 (EAL Edition), page 268

Reg HSE GS38

Q5. You are about to test in an office where the servers run 24 hours a day. What should be obtained before isolating their circuits?

Show answer

Answer: B. Approval to shut down systems that testing might damage

  • Before testing, obtain approval to shut down systems that might be damaged, for example computers may crash if switched off.
  • Ventilation and fume extraction will also stop when supplies are disconnected.

Check with the occupier first, then isolate.

Why the others are wrong:

A: a certificate records completed work, it is not permission to shut down.

C: the UPS calibration is not relevant to permission.

D: shutting down computer systems without approval can cause them to crash.

Memory trick:

Ask before you crash their computers.

Find it in the book

Linsley, Electrical Installation Work Level 3 (EAL Edition), page 270

Reg EAL Ch4 safe working

Q6. What does the book say should be your first objective when starting safe isolation procedures?

Show answer

Answer: C. Carry out a risk assessment of the working area

  • Your first objective when carrying out safe isolation is a risk assessment of your working area.
  • Testing procedures can expose electricians to live supplies, so hazards must be identified first.

Assess, then isolate.

Why the others are wrong:

A: that is a preparation step for some tests, not the first objective.

B: paperwork may help but is not the first safety objective.

D: this is a functional check, not the start of safe isolation.

Memory trick:

Assess before you isolate.

Find it in the book

Linsley, Electrical Installation Work Level 3 (EAL Edition), page 268

Reg EAL Ch4 Safety first

Want 174 more QELTK3/006 questions? Start a free timed mock.

Start a free mock

Full mock, no card needed. Full workouts on the first 5 questions.

Other QELTK3/006 topics

Revise this topic