CITB Plumbing (JIB): Gas, hot work and fire on plumbing jobs practice questions

Written by Acacio Oliveira, founder of FreeMocks, plumbing and heating engineer (F-Gas registered).

40 of our 200 CITB HS&E Specialist Test: Plumbing (JIB) (CITB-SPEC-PLUM) questions are on gas, hot work and fire on plumbing jobs, about 20% of the bank. Try 6 below with full worked answers, then practise the rest in a timed mock.

Practice questions

Pick an answer to see why it's right, why the others are wrong, and the page in the book.

Q1. Which job does NOT need Gas Safe registration, although the person must still be competent?

Show answer

Answer: A. Swapping an empty LPG cylinder for a full one

  • Gas storage vessels are not gas fittings, so changing cylinders does not require Gas Safe registration.
  • People doing it still need competence and must follow supplier or manufacturer instructions.

Installing or replacing a tank that involves work on service pipework or other fittings needs a registered engineer.

Why the others are wrong:

B: work on installation pipework needs Gas Safe registration.

C: the guidance says this involves gas fittings and needs a registered engineer.

D: work on a gas appliance needs an HSE-approved class of persons.

Memory trick:

Cylinder swap: competent. Pipework: registered.

Find it in the book

HSE L56 (5th edition, 2018), page 24

Reg Gas Safety (Installation and Use) Regulations 1998, regulation 3(3) to (4); HSE L56 guidance paragraphs 95 to 96

Q2. Which type of gas appliance may be installed in a bathroom or shower room?

Show answer

Answer: C. Only a room-sealed appliance

  • Regulation 30(1): no gas appliance may be installed in a bathroom or shower room unless it is room-sealed.
  • This includes a cupboard in the room, or a cupboard next to it that has an air vent into the room.

Different rules apply to rooms used for sleeping.

Why the others are wrong:

A: a cut-out does not make an appliance room-sealed.

B: the 14 kW rule applies to sleeping rooms, not bathrooms.

D: a flueless heater is not room-sealed, alarm or not.

Memory trick:

Bathroom gas? Room-sealed only.

Find it in the book

HSE L56 (5th edition, 2018), page 59

Reg Gas Safety (Installation and Use) Regulations 1998, regulation 30(1)

Q3. A Gas Safe engineer needs to use a blowtorch on pipework that has contained gas. What does the guidance advise?

Show answer

Answer: A. Isolate the supply and purge the gas before using the torch

  • Regulation 6(4): no one exposing gasways that contain or have contained gas may use a source of ignition that could cause fire or explosion.
  • Sources of ignition include blow-lamps and hot-air guns; gasways should generally be purged of gas before using a blow torch.

A safe system of work includes effective isolation of the gas supply.

Why the others are wrong:

B: moving the flame does not remove the risk of fire or explosion.

C: ventilation alone is not the safe system described; the gasway should be purged.

D: the guidance lists hot-air guns as sources of ignition.

Memory trick:

Purge before you play with fire.

Find it in the book

HSE L56 (5th edition, 2018), page 28

Reg Gas Safety (Installation and Use) Regulations 1998, regulation 6(4); HSE L56 guidance paragraph 120

Q4. After work that might affect the gas tightness of an installation, how far must it be tested?

Show answer

Answer: C. At least to the nearest valves upstream and downstream

  • Regulation 6(6): after work that might affect gas tightness, test immediately, at least as far as the nearest valves upstream and downstream.
  • In homes the test normally covers pipework from the meter or emergency control valve to the appliance shut-off device.

This test is also called a soundness or pressure decay test.

Why the others are wrong:

A: the minimum is the nearest valves either side of the work.

B: the test must reach the nearest valve upstream as well.

D: the regulation requires a wider test than the joints alone.

Memory trick:

Valve to valve, straight after the work.

Find it in the book

HSE L56 (5th edition, 2018), page 29

Reg Gas Safety (Installation and Use) Regulations 1998, regulation 6(6); HSE L56 guidance paragraph 125

Q5. A neighbour asks you to swap their gas hob as a favour. You are a plumber but not Gas Safe registered. What is the legal position?

Show answer

Answer: C. Anyone doing gas work must be competent, paid or not

  • Regulation 3(1): no person may work on a gas fitting unless they are competent to do so.
  • The guidance says DIY gas engineers and people doing favours for friends and relatives must still be competent.

A business doing gas work must also be a member of an HSE-approved class of persons, which at publication meant Gas Safe Register.

Why the others are wrong:

A: the like-for-like exceptions only cover certain hose and regulator replacements, not appliances.

B: the guidance says people doing favours for friends and relatives still need to be competent.

D: isolating the supply does not make an unqualified person competent to do gas work.

Memory trick:

Paid or unpaid, gas work needs a competent person.

Find it in the book

HSE L56 (5th edition, 2018), page 23

Reg Gas Safety (Installation and Use) Regulations 1998, regulation 3(1); HSE L56 guidance paragraph 83

Q6. HSE defines hot work as any process that generates flame, sparks or heat. Which plumbing task counts as hot work?

Show answer

Answer: A. Using an electric soldering iron or heat gun

  • Hot work is any process that generates flame, sparks or heat.
  • HSE lists soldering irons and heat guns, grinding and cutting metal, and oxy-fuel work as common hot works.

Electric tools can still be hot work if they produce heat.

Why the others are wrong:

B: a hand cutter is a cold cutting method.

C: tightening a compression joint does not generate flame, sparks or heat.

D: push-fit is a cold method that produces no flame, sparks or heat.

Memory trick:

Flame, spark or heat: it's hot work.

Find it in the book

HSE HSG168 (3rd edition, 2022), page 24

Reg HSE HSG168, paragraphs 118 and 120

Want 194 more CITB Plumbing (JIB) questions? Start a free timed mock.

Start a free mock

Full mock, no card needed. Full workouts on the first 5 questions.

Other CITB Plumbing (JIB) topics

Free official guides for this topic

Our questions are written from these documents. Download them free to revise from the source.

© Crown copyright (HSE). Unchanged copies, reproduced under the Open Government Licence v3.0. FreeMocks is not connected to or endorsed by HSE or the government.

Revise this topic