CITB Plumbing (JIB): Core: general safety practice questions

Written by Acacio Oliveira, founder of FreeMocks, plumbing and heating engineer (F-Gas registered).

16 of our 200 CITB HS&E Specialist Test: Plumbing (JIB) (CITB-SPEC-PLUM) questions are on core: general safety, about 8% of the bank. Try 6 below with full worked answers, then practise the rest in a timed mock.

Practice questions

Pick an answer to see why it's right, why the others are wrong, and the page in the book.

Q1. What does HSE advise before plugging in or unplugging a tool?

Show answer

Answer: C. Switch off the tool and the socket where possible

  • Where possible, tools and power socket outlets should be switched off before plugging in or unplugging.
  • Switch off and unplug equipment before cleaning or making adjustments.

Simple habits prevent many electrical injuries.

Why the others are wrong:

A: tools should be switched off first.

B: the RCD is tested with its test button.

D: this damages the cable and connections.

Memory trick:

Off, then plug.

Find it in the book

HSE INDG231 (rev1, 2012), page 4

Reg HSE INDG231, work safely

Q2. What does HSE say about normal mains voltage of 230 V AC?

Show answer

Answer: A. It can kill

  • The main hazards include contact with live parts causing shock and burns.
  • Normal mains voltage, 230 volts AC, can kill.

Even non-fatal shocks can cause falls from ladders and platforms.

Why the others are wrong:

B: 230 V can kill in any conditions, though wet makes it worse.

C: contact with 230 V live parts can cause fatal shock.

D: a fuse protects the circuit, not the person.

Memory trick:

230 volts can kill.

Find it in the book

HSE INDG231 (rev1, 2012), page 1

Reg HSE INDG231, what are the hazards?

Q3. The RCD keeps tripping when you plug in your drill. What does this tell you?

Show answer

Answer: D. There is a fault; check it before using it again

  • If an RCD trips, it is a sign there is a fault: check the system before using it again.
  • Never bypass an RCD; if it trips often and no fault is found, consult the manufacturer.

Damaged equipment should be taken out of use.

Why the others are wrong:

A: an RCD must never be bypassed.

B: a bigger fuse would not fix the fault the RCD has found.

C: a trip is a sign of a fault that must be checked.

Memory trick:

RCD trips? Find the fault.

Find it in the book

HSE INDG231 (rev1, 2012), page 3

Reg HSE INDG231, provide a safety device

Q4. How should two lengths of flexible cable be joined?

Show answer

Answer: A. With proper connectors or cable couplers

  • Use proper connectors or cable couplers to join lengths of cable.
  • Do not use strip connector blocks covered in insulating tape.

The outer sheath should be firmly clamped where the cable enters plugs and equipment.

Why the others are wrong:

B: twisted and taped joints are unsafe.

C: this is not a proper connector.

D: HSE says not to use strip connectors covered in tape.

Memory trick:

Couplers, not choc block and tape.

Find it in the book

HSE INDG231 (rev1, 2012), page 2

Reg HSE INDG231, provide safe and suitable equipment

Q5. Which extinguishers are suitable for a fire involving electrical equipment?

Show answer

Answer: C. Carbon dioxide or dry powder

  • For electrical items, use a carbon dioxide (CO2) or dry powder extinguisher.
  • Wood, paper and cloth: water, foam or multi-purpose powder; flammable liquids: powder or foam.

Dry powder does not cool and can reduce visibility.

Why the others are wrong:

A: water must not be used on electrical fires.

B: foam must not be used on electrical fires.

D: water and foam must not be used on electrical fires.

Memory trick:

Electrics: CO2 or powder.

Find it in the book

HSE HSG168 (3rd edition, 2022), pages 51 to 52

Reg HSE HSG168, paragraph 293 and Figure 17

Q6. How should a fire point on site be made easy to identify?

Show answer

Answer: B. With a mainly red stand or a proper safety sign

  • Identify a fire point by a stand that is substantially red or an appropriate safety sign.
  • Fire extinguishers should be on hooks or stands to keep them off the ground.

Extinguishers are also needed for specific activities such as hot work.

Why the others are wrong:

A: this is not the marking described.

C: this is not the marking described.

D: extinguishers should be on hooks or stands, off the ground.

Memory trick:

Fire point: red and signed.

Find it in the book

HSE HSG168 (3rd edition, 2022), page 51

Reg HSE HSG168, paragraph 291

Want 194 more CITB Plumbing (JIB) questions? Start a free timed mock.

Start a free mock

Full mock, no card needed. Full workouts on the first 5 questions.

Other CITB Plumbing (JIB) topics

Free official guides for this topic

Our questions are written from these documents. Download them free to revise from the source.

© Crown copyright (HSE). Unchanged copies, reproduced under the Open Government Licence v3.0. FreeMocks is not connected to or endorsed by HSE or the government.

Revise this topic