AM2 Knowledge Test: BS 7671 requirements practice questions

Written by Acacio Oliveira, founder of FreeMocks, plumbing and heating engineer (F-Gas registered).

75 of our 240 AM2 Assessment of Applied Knowledge (Section E) (AM2) questions are on bs 7671 requirements, about 31% of the bank. Try 6 below with full worked answers, then practise the rest in a timed mock.

Regulations that come up most

The regulation groups our bs 7671 requirements questions test most often. Know where these are in your book before the exam.

  • 411.3 · 4 questions
  • 537.3 · 4 questions
  • 701.32 · 4 questions
  • 521.5 · 3 questions
  • 522.6 · 3 questions
  • 433.1 · 2 questions
  • 521.10 · 2 questions
  • 522.8 · 2 questions

Practice questions

Pick an answer to see why it's right, why the others are wrong, and the page in the book.

Q1. You're fitting a supplementary bond between a copper hot pipe and a copper cold pipe in an airing cupboard. Neither is connected to an exposed-conductive-part, and the bonding cable is sheathed. What is the minimum size?

Show answer

Answer: B. 2.5 mm²

  • 544.2.3: between two extraneous-conductive-parts, at least 2.5 mm² if sheathed or mechanically protected, 4 mm² if not.
  • If one part is also connected to an exposed-conductive-part, 544.2.2 applies instead.

The pipes are both extraneous-conductive-parts, so 2.5 mm² sheathed is enough.

Why the others are wrong:

A: 4 mm² applies only where there is no mechanical protection.

C: 1.5 mm² is below the minimum for a supplementary bonding conductor.

D: 6 mm² is the main bonding minimum, not supplementary.

Memory trick:

Pipe to pipe: 2.5 covered, 4 bare.

Find it in the book

BS 7671:2018+A4:2026, page 216

Reg 544.2.3

Q2. On the rig, an SWA cable runs from the main consumer unit to a separate sub-board, which feeds the motor and socket circuits. What is the SWA cable classed as?

Show answer

Answer: C. A distribution circuit

  • A distribution circuit supplies a distribution board or switchgear (sometimes called a sub-main).
  • A final circuit connects directly to current-using equipment or to socket-outlets.

The SWA feeds a board, so it is a distribution circuit.

Why the others are wrong:

A: a ring final is a type of final circuit feeding outlets, not a board.

B: a final circuit connects directly to current-using equipment or socket-outlets, not to a distribution board.

D: the origin is where electrical energy is delivered to the installation.

Memory trick:

Feeds a board = distribution. Feeds a load = final.

Reg Part 2

Q3. A three-phase DOL motor is fed by four-core 70 °C thermoplastic SWA on a perforated horizontal tray (Reference Method E), in a single layer touching two other multicore cables. Ambient is 35 °C and the circuit-breaker is 32 A. What is the smallest size that meets the current-carrying capacity requirement?

Show answer

Answer: D. 6 mm²

  • Table 4B1: 35 °C: Ca = 0.94.
  • Table 4C1, item 3 (single layer multicore on perforated tray), 3 cables: Cg = 0.82.
  • It >= 32 / (0.94 x 0.82) = 41.5 A.
  • Table 4D4A, Method E, three- or four-core: 4 mm² = 35 A, 6 mm² = 45 A.

Use the tray row of Table 4C1, not the bunched row.

Why the others are wrong:

A: 2.5 mm² gives only 26 A, which is less than the 32 A device rating even before factors.

B: 4 mm² gives 35 A in Method E for three-phase, below the 41.5 A needed.

C: 6 mm² at 45 A already exceeds the 41.5 A needed.

The maths

Ca = 0.94, Cg = 0.82 (3 multicore on perforated tray)
It >= 32 / (0.94 x 0.82) = 41.5 A
4 mm2 = 35 A (fail), 6 mm2 = 45 A (pass)

Memory trick:

Tray cables keep cooler, so use the tray grouping row, not the bunched one.

Find it in the book

BS 7671:2018+A4:2026, page 485

Reg Appx 4 Tables 4B1, 4C1, 4D4A

Q4. You need a means of isolation beside the three-phase motor on the rig. Which type of device must NOT be used for that isolation?

Show answer

Answer: B. A semiconductor (solid-state) switching device

  • Devices for isolation must be of a type whose isolation function is recognised by the product standard or Table 537.4.
  • Semiconductor devices shall not be used as isolating devices.

A solid-state device can stop current without opening a contact gap, so it does not give safe isolation.

Why the others are wrong:

A: switch-disconnectors are listed as suitable for isolation.

C: a device suitable and marked for isolation meets the requirement.

D: circuit-breakers to BS EN 60898 are listed as suitable for isolation.

Memory trick:

No air gap, no isolation: semiconductors can't isolate.

Find it in the book

BS 7671:2018+A4:2026, page 195

Reg 537.2.2

Q5. A radial has a design current of 28 A and is wired in a cable whose Iz is 29 A. It is protected by a 32 A circuit-breaker. Which condition of Regulation 433.1.1 is not met?

Show answer

Answer: C. In must not exceed the cable's Iz

  • 433.1.1(a): In ≥ Ib. 32 ≥ 28, met.
  • 433.1.1(b): In ≤ Iz. 32 > 29, not met.

The cable could be overloaded without the device tripping. Use a larger cable or a lower-rated device that still carries Ib.

Why the others are wrong:

A: Ib must not exceed Iz; here it doesn't, and that is correct.

B: 32 A is more than the 28 A design current, so this condition is met.

D: there is no rule doubling Iz.

Memory trick:

Device sits between load and cable, never above the cable.

Find it in the book

BS 7671:2018+A4:2026, page 103

Reg 433.1.1

Q6. A cable runs 60 mm deep inside a metal-stud plasterboard partition. Which option satisfies Table 52.1 for this situation?

Show answer

Answer: A. Additional protection by a 30 mA RCD

  • For a wall or partition with metallic parts, a cable 50 mm or deeper must either have additional protection by an RCD to 415.1.1, or comply with 522.6.204 (earthed metallic covering, earthed conduit, mechanical protection, or SELV/PELV).
  • Depth alone gives no exemption where metal studs are present, because screws can drive through the stud into the cable.

Metal parts change the answer.

Why the others are wrong:

B: the 'no additional protection' entry applies only to walls without metallic parts.

C: in a wall with metallic parts at this depth the requirement is RCD protection or a 522.6.204 method, not a zone alone.

D: clip type has nothing to do with the concealment requirements of Table 52.1.

Memory trick:

Metal in the wall? Depth won't save you: RCD or 522.6.204.

Find it in the book

BS 7671:2018+A4:2026, page 152

Reg Table 52.1

Want 234 more AM2 Knowledge Test questions? Start a free timed mock.

Start a free mock

Full mock, no card needed. Full workouts on the first 5 questions.

Other AM2 Knowledge Test topics

Revise this topic