MCS Heat Pumps and BUS: Installation, commissioning and handover (MIS 3005-I) practice questions

Written by Acacio Oliveira, founder of FreeMocks, plumbing and heating engineer (F-Gas registered).

24 of our 160 MCS Heat Pump Installer and Boiler Upgrade Scheme (MCS-HP-BUS) questions are on installation, commissioning and handover (mis 3005-i), about 15% of the bank. Try 6 below with full worked answers, then practise the rest in a timed mock.

Practice questions

Pick an answer to see why it's right, why the others are wrong, and the page in the book.

Q1. How must a heat pump system be commissioned under MIS 3005-I:2025?

Show answer

Answer: A. To a documented procedure, e.g. a maker's checklist

  • Commission to a documented procedure so the system is safe, installed to the standard and manufacturer requirements, and operating to the design.
  • Manufacturer checklists or the example in the appendix are suitable.

Some manufacturers need their checklist for warranty.

Why the others are wrong:

B: it must be safe, compliant and operating to the design.

C: commissioning is the contractor's job.

D: a documented procedure is required.

Memory trick:

Write it down as you prove it works.

Find it in the book

MCS MIS 3005-I:2025 V1.0, page 12

Reg MCS MIS 3005-I:2025 V1.0, clause 4.1.1

Q2. Under MIS 3005-I:2025, when can a heat pump installer self-certify Building Regulations compliance instead of using building control?

Show answer

Answer: D. Only when registered with an approved CPS for that work

  • Self-certification is only allowed where the work is done by someone registered with an approved Competent Persons Scheme for that scope.
  • Where you are responsible for notification, it must be completed before handover.

Otherwise building control approval is needed.

Why the others are wrong:

A: system size does not grant self-certification.

B: MCS certification is not a Competent Persons Scheme registration.

C: customer agreement does not allow self-certification.

Memory trick:

CPS or building control, not MCS alone.

Find it in the book

MCS MIS 3005-I:2025 V1.0, page 9

Reg MCS MIS 3005-I:2025 V1.0, clause 3.1.6

Q3. The new heat pump controller connects to the customer's home Wi-Fi. What does MIS 3005-I:2025 require about its login details?

Show answer

Answer: B. Update the credentials in consultation with the customer

  • The data privacy and security of the home area network shall be maintained.
  • Network access credentials shall be updated in consultation with the customer.

Components should also meet ETSI TS 103 645.

Why the others are wrong:

A: default credentials must be updated to keep the home network secure.

C: a shared password across jobs does not keep the site's network secure.

D: this would expose the network and is not what the standard asks.

Memory trick:

New box, new password, agreed with the owner.

Find it in the book

MCS MIS 3005-I:2025 V1.0, page 10

Reg MCS MIS 3005-I:2025 V1.0, clause 3.5.3

Q4. Under the MCS Installer Operating Requirements 2.0, what should you follow to support a heat pump handover?

Show answer

Answer: D. The technology specific MCS Handover Checklists

  • A key duty is an effective handover, so the customer understands their new system.
  • Follow the technology specific Handover Checklists published on the MCS website.

The Customer Commitment lists the minimum handover pack.

Why the others are wrong:

A: Ofgem's portal is for applications, not MCS handover.

B: the IOR points to the MCS Handover Checklists.

C: the DNO form is not a handover checklist.

Memory trick:

Hand over by the MCS checklist.

Find it in the book

MCS Installer Operating Requirements 2.0 (2026), page 17

Reg MCS Installer Operating Requirements 2.0 (2026), clause 6.4

Q5. On a split heat pump system, who should evacuate the system and charge the refrigerant, according to the MIS 3005-I:2025 commissioning checklist?

Show answer

Answer: A. An F-Gas registered operative

  • The commissioning checklist records that split systems were evacuated and charged by an F-Gas registered operative.
  • It also records the refrigerant type and charge in kg.

Monobloc units avoid site refrigerant work.

Why the others are wrong:

B: Gas Safe covers fuel gas work, not refrigerant.

C: CPS electrical registration does not cover refrigerant handling.

D: refrigerant work must be done by an F-Gas registered operative.

Memory trick:

Refrigerant needs F-Gas hands.

Find it in the book

MCS MIS 3005-I:2025 V1.0, page 17

Reg MCS MIS 3005-I:2025 V1.0, Appendix A, split systems

Q6. Under MIS 3005-I:2025 clause 3.3.2, which pair of conditions must all installed equipment meet?

Show answer

Answer: D. Fit for purpose, and conformity assessed and correctly marked

  • All equipment installed shall be fit for its purpose in the installation.
  • It must also have completed the conformity assessment process and be appropriately marked by a Notified Body under the relevant legislation.

The standard gives the CE mark as an example of that marking.

Why the others are wrong:

A: clause 3.3.2 sets no age limit; it asks for conformity assessment and correct marking.

B: the PEL is a BUS rule, not one of the clause 3.3.2 conditions for all equipment.

C: warranty length is not one of the clause 3.3.2 conditions.

Memory trick:

Fit for the job, and marked to prove it.

Find it in the book

MCS MIS 3005-I:2025 V1.0, pages 9 to 10

Reg MCS MIS 3005-I:2025 V1.0, clause 3.3.2

Want 154 more MCS Heat Pumps and BUS questions? Start a free timed mock.

Start a free mock

Full mock, no card needed. Full workouts on the first 5 questions.

Other MCS Heat Pumps and BUS topics

Free official guides for this topic

Our questions are written from these documents. Download them free to revise from the source.

© Crown copyright (Ofgem, GOV.UK). Unchanged copies, reproduced under the Open Government Licence v3.0. FreeMocks is not connected to or endorsed by HSE or the government.

Revise this topic