MCS Heat Pumps and BUS: Heat loss and system design (MIS 3005-D) practice questions

Written by Acacio Oliveira, founder of FreeMocks, plumbing and heating engineer (F-Gas registered).

28 of our 160 MCS Heat Pump Installer and Boiler Upgrade Scheme (MCS-HP-BUS) questions are on heat loss and system design (mis 3005-d), about 18% of the bank. Try 6 below with full worked answers, then practise the rest in a timed mock.

Practice questions

Pick an answer to see why it's right, why the others are wrong, and the page in the book.

Q1. In an air-to-air design, a utility room is not a habitable room and has no space for an indoor unit. What does MIS 3005-D:2025 say?

Show answer

Answer: B. Decide if it needs heat and how, such as a separate source

  • Every habitable room shall have an indoor unit.
  • For rooms that are not habitable or cannot fit a unit, consider whether heating is required and how, for example a separate heat source.

Extra heat sources may add running costs.

Why the others are wrong:

A: the requirement is for habitable rooms; other rooms are considered separately.

C: the note says to consider whether heating is needed.

D: oversizing the outdoor unit is not the answer given.

Memory trick:

Not habitable? Decide if it needs heat.

Find it in the book

MCS MIS 3005-D:2025 V2.0, page 13

Reg MCS MIS 3005-D:2025 V2.0, clause 3.4.3(h), note

Q2. Under MIS 3005-D:2025, what must be clearly stated in the contract for a hybrid heat pump system?

Show answer

Answer: D. The heat pump's designed share of space heating and hot water

  • The contract must state what proportion of space heating the heat pump is designed to provide (excluding any electric heater).
  • It must also state the proportion of domestic hot water from the heat pump.

The control philosophy must prioritise the heat pump and be agreed with the user.

Why the others are wrong:

A: the contract must state the heat pump share, not a gas certificate.

B: the requirement is about design proportions, not a bill estimate.

C: the controller is a design point; the proportions must be stated.

Memory trick:

Hybrid contract: say how much is heat pump.

Find it in the book

MCS MIS 3005-D:2025 V2.0, page 12

Reg MCS MIS 3005-D:2025 V2.0, clause 3.4.2(g)

Q3. In MIS 3005-D:2025, what does the word 'must' indicate?

Show answer

Answer: B. A requirement by law at the time of publication

  • 'Must' identifies a requirement by law at the time of publication.
  • 'Shall' is to be complied with in full without deviation; 'should' allows reasonable justification.

Compliance with the standard does not give immunity from legal obligations.

Why the others are wrong:

A: that describes 'should'.

C: 'must' is stronger than a recommendation; it is a legal requirement.

D: manufacturer instructions are a separate topic.

Memory trick:

Must is the law.

Find it in the book

MCS MIS 3005-D:2025 V2.0, page 6

Reg MCS MIS 3005-D:2025 V2.0, Foreword

Q4. Which of these systems is expressly excluded from MIS 3005-D:2025?

Show answer

Answer: C. A direct expansion (DX) ground-loop system

  • Excluded: cooling only systems, DX ground-loop systems and heat pumps extracting heat from loft spaces.
  • Monobloc, split, reversible and thermally driven heat pumps are in scope.

The same exclusions appear in MIS 3005-I.

Why the others are wrong:

A: split units are in scope; the standard covers monobloc and split.

B: both vapour compression and thermally driven heat pumps are covered.

D: reversible systems are included but must be optimised for heating.

Memory trick:

DX, loft and cool-only are out.

Find it in the book

MCS MIS 3005-D:2025 V2.0, page 7

Reg MCS MIS 3005-D:2025 V2.0, section 1

Q5. A borehole design needs a minimum active length Lb of 110 m. Using Rpt from MIS 3005-D:2025, what is the minimum length of pipe Lp in the active elements?

Show answer

Answer: C. 220 m

  • Lp = Lb x Rpt.
  • Rpt = 2 for boreholes, 1 for horizontal loops, and the look-up ratio for slinkies.

Lp does not include header pipes.

Why the others are wrong:

A: 110 m uses Rpt = 1, which applies to horizontal loops, not boreholes.

B: 55 m divides by 2 instead of multiplying.

D: 330 m uses a ratio of 3, which is not given for boreholes.

The maths

Lp = Lb x Rpt = 110 m x 2 = 220 m of pipe.

Memory trick:

Boreholes go down and back: times two.

Find it in the book

MCS MIS 3005-D:2025 V2.0, page 19

Reg MCS MIS 3005-D:2025 V2.0, clause 3.7.5(g)

Q6. Which specification does MIS 3005-D:2025 name for hot water cylinders suitable for use with heat pumps?

Show answer

Answer: B. HWA 002:2020

  • The Hot Water Association specification HWA 002:2020 covers cylinders for use with heat pumps.
  • Cylinders labelled to it satisfy the heat exchanger requirement.

Heat pump coils need more surface area because flow temperatures are lower.

Why the others are wrong:

A: BS 1566-1 is about cylinder standing heat loss for reused cylinders.

C: BS EN 805 is used for ground loop pressure testing.

D: MCS 020 a) is the sound calculation for permitted development.

Memory trick:

HWA for heat pump cylinders.

Find it in the book

MCS MIS 3005-D:2025 V2.0, page 15

Reg MCS MIS 3005-D:2025 V2.0, clause 3.5.4, note

Want 154 more MCS Heat Pumps and BUS questions? Start a free timed mock.

Start a free mock

Full mock, no card needed. Full workouts on the first 5 questions.

Other MCS Heat Pumps and BUS topics

Free official guides for this topic

Our questions are written from these documents. Download them free to revise from the source.

© Crown copyright (Ofgem, GOV.UK). Unchanged copies, reproduced under the Open Government Licence v3.0. FreeMocks is not connected to or endorsed by HSE or the government.

Revise this topic