Electrical Safety: Dangers: shock, burns, fire and arcing practice questions

Written by Acacio Oliveira, founder of FreeMocks, plumbing and heating engineer (F-Gas registered).

30 of our 120 Electrical Safety Awareness (ELEC-SAFETY) questions are on dangers: shock, burns, fire and arcing, about 25% of the bank. Try 6 below with full worked answers, then practise the rest in a timed mock.

Practice questions

Pick an answer to see why it's right, why the others are wrong, and the page in the book.

Q1. Which of these mainly influences the likely effects of a shock current on the body?

Show answer

Answer: C. How long the current flows

  • HSR25 says the effects of shock current are mainly influenced by voltage, frequency, duration and any impedance in the current path.
  • Severity also depends on the path the current takes through the body.

The longer current flows, the more harm it can do, which is why fast disconnection matters.

Why the others are wrong:

A: cable length is not one of the listed factors.

B: the type of tool is not one of the listed factors.

D: time of day has no bearing on the listed factors.

Memory trick:

Volts, hertz, time, resistance.

Find it in the book

HSE HSR25 (3rd edition, 2015), page 11

Reg Electricity at Work Regulations 1989, reg 2 (HSE HSR25, para 33)

Q2. A car battery is short-circuited by a dropped spanner. The voltage is too low to give a harmful shock. What can still happen?

Show answer

Answer: A. Conductors can overheat and the battery may explode

  • Even at extra-low voltages, an arc can occur, overheated conductors can burn, or an explosive atmosphere can be ignited.
  • HSG85 gives the example of a short-circuited car battery, which may explode.

No shock risk does not mean no electrical danger.

Why the others are wrong:

B: HSG85 says arcs, burns and explosions can happen even at extra-low voltage.

C: the danger here is heat, arcing and explosion, not shock.

D: HSG85 warns the battery itself could explode.

Memory trick:

Low volts, big amps, still a bang.

Find it in the book

HSE HSG85 (3rd edition, 2013), page 7

Reg HSE HSG85, para 11

Q3. What is meant by 'electrocution'?

Show answer

Answer: B. Death caused by an electric shock

  • HSG85: electric shocks do not always cause lasting injury.
  • In certain circumstances they result in death, known as electrocution.

Not every shock is electrocution, but any shock can become one.

Why the others are wrong:

A: HSG85 uses electrocution for a shock that results in death.

C: arc burns are a separate injury from electrocution.

D: electrocution is about people, not equipment.

Memory trick:

Electrocution = electric + execution.

Find it in the book

HSE HSG85 (3rd edition, 2013), page 6

Reg HSE HSG85, para 4

Q4. Roughly what size of current does HSR25 say can be enough to cause a fatal electric shock?

Show answer

Answer: C. A few milliamps (mA)

  • HSR25: quite low currents, of the order of only a few milliamps, can cause a fatal shock.
  • Severity depends on the size, duration and path of the current.

This is why fuses alone do not protect people from shock.

Why the others are wrong:

A: HSR25 says currents of only a few milliamps can be fatal, far less than 1 A.

B: a 13 A fuse protects the cable; it will not stop a fatal shock of a few milliamps.

D: fatal shocks happen at thousands of times less current than this.

Memory trick:

Milliamps kill; fuses protect cables.

Find it in the book

HSE HSR25 (3rd edition, 2015), page 11

Reg Electricity at Work Regulations 1989, reg 2 (HSE HSR25, para 32)

Q5. What causes an electric burn, as opposed to a burn from a fire?

Show answer

Answer: C. Heating as current passes through body tissue

  • Electric burns are due to the heating effect of current passing through body tissues.
  • They are often found in and on the skin at the point of contact.

They are usually painful, very slow to heal and often scar.

Why the others are wrong:

A: that is part of arcing injury, which HSR25 treats separately.

B: that would be a fire injury, not an electric burn.

D: that is a heat burn from a hot surface, not an electric burn.

Memory trick:

Electric burn: current cooks from the inside.

Find it in the book

HSE HSR25 (3rd edition, 2015), page 11

Reg Electricity at Work Regulations 1989, reg 2 (HSE HSR25, para 37)

Q6. In HSE electrical guidance, what counts as 'high voltage'?

Show answer

Answer: B. Above 1000 V ac or 1500 V dc

  • HSR25: high voltage is above 1000 V ac or 1500 V dc.
  • Low voltage is up to and including those values, so 230 V and 400 V are low voltage.

'Low voltage' does not mean safe: 230 V can kill.

Why the others are wrong:

A: 230 V is normal mains, which is low voltage in HSE guidance.

C: 400 V three-phase is still low voltage.

D: these are the HSG85 thresholds for a hazardous exposed live part.

Memory trick:

1000 ac, 1500 dc: over that is HV.

Find it in the book

HSE HSR25 (3rd edition, 2015), page 13

Reg Electricity at Work Regulations 1989 (HSE HSR25, para 49)

Want 114 more Electrical Safety questions? Start a free timed mock.

Start a free mock

Full mock, no card needed. Full workouts on the first 5 questions.

Other Electrical Safety topics

Free official guides for this topic

Our questions are written from these documents. Download them free to revise from the source.

© Crown copyright (HSE). Unchanged copies, reproduced under the Open Government Licence v3.0. FreeMocks is not connected to or endorsed by HSE or the government.

Revise this topic