ECS HS&E: Personal Protective Equipment at Work practice questions

Written by Acacio Oliveira, founder of FreeMocks, plumbing and heating engineer (F-Gas registered).

31 of our 400 ECS Health, Safety and Environmental Assessment (ECS-HSE) questions are on personal protective equipment at work, about 8% of the bank. Try 6 below with full worked answers, then practise the rest in a timed mock.

Practice questions

Pick an answer to see why it's right, why the others are wrong, and the page in the book.

Q1. A colleague's helmet is tilted back and loose so he can look upwards more easily. What should he do?

Show answer

Answer: C. Sit it square on his head and adjust it

  • A safety helmet should be worn square on the head and properly adjusted.
  • All PPE should be used in line with the manufacturer's instructions, which cover how to fit and wear it.

Why the others are wrong:

A: it should be properly adjusted to fit.

B: a bump cap does not protect against falling objects.

D: a helmet should be worn square on the head, not tilted.

Memory trick:

Square and snug, peak to the front.

Reg PPE at Work Regulations

Q2. A new starter asks why the hi-vis rule is enforced so strictly on roadworks. What is the best answer?

Show answer

Answer: B. Moving vehicles often strike and injure workers

  • A high visibility vest lets road users and plant operators see you.
  • Many workers are struck and injured, often seriously, by moving vehicles.

That is why hi-vis is so important on roads.

Why the others are wrong:

A: the purpose is to be seen by traffic, not to advertise.

C: the vest is for safety, not attendance.

D: a hi-vis vest is not worn for weather protection.

Memory trick:

Hi-vis = high chance they see you.

Reg PPE at Work Regulations

Q3. On most construction sites, where do site rules normally allow you to remove your safety helmet?

Show answer

Answer: A. In designated safe areas

  • Site rules normally require head protection to be worn other than in designated safe areas.
  • Despite controls, a risk of head injury almost always remains on construction sites.

Why the others are wrong:

B: being indoors does not remove the risk of head injury.

C: height above ground is not the test for removing a helmet.

D: you can still strike your head or be hit by falling items.

Memory trick:

Helmet off only where the site says it's safe.

Reg Site rules

Q4. Three operatives are working in a dusty area. One wears self-contained breathing apparatus, one a compressed airline breathing helmet and one a half mask dust respirator. Which statement is correct?

Show answer

Answer: B. The half mask wearer has the lowest protection

  • Of these options, a half mask dust respirator gives the least protection.
  • Protection factors for RPE are set out in HSE guidance HSG53, Respiratory protective equipment at work.

Why the others are wrong:

A: these types of RPE have different protection factors, so they are not equal.

C: self-contained breathing apparatus gives a much higher level of protection than a half mask.

D: an airline-fed helmet gives more protection than a simple half mask dust respirator.

Memory trick:

Half a mask, half the protection: it sits at the bottom of the list.

Reg Respiratory protective equipment

Q5. Head protection is required by law unless which condition applies?

Show answer

Answer: D. There is no foreseeable risk of head injury

  • If there is no risk of injury to the head, hard hats are not required by law.
  • On construction sites, despite controls, a risk of head injury almost always remains, and site rules require helmets other than in designated safe areas.

Why the others are wrong:

A: nobody can opt out of required protection.

B: hot weather does not remove the risk of head injury.

C: a short task can still carry a risk of head injury.

Memory trick:

No head risk, no hat law. On site, that's rare.

Reg PPE at Work Regulations

Q6. An electrician is working above the ceiling of a finished, occupied office. Nothing can fall or swing towards him, but he keeps hitting his head on fixed ductwork. Which head protection could be suitable?

Show answer

Answer: D. A bump cap

  • Bump caps protect against striking fixed obstacles, scalping and entanglement.
  • They do not protect against falling or swinging objects.

A bump cap is suitable only where there is no foreseeable risk from falling or swinging objects, as in this case.

Why the others are wrong:

A: fabric gives no real protection against striking obstacles.

B: there is still a risk of striking fixed obstacles.

C: a visor protects the face, not the scalp from knocks.

Memory trick:

Bump cap for bumps, hard hat for drops.

Reg PPE at Work Regulations

Want 394 more ECS HS&E questions? Start a free timed mock.

Start a free mock

Full mock, no card needed. Full workouts on the first 5 questions.

Other ECS HS&E topics

Revise this topic