ECS HS&E: Electrotechnical practice questions

Written by Acacio Oliveira, founder of FreeMocks, plumbing and heating engineer (F-Gas registered).

48 of our 400 ECS Health, Safety and Environmental Assessment (ECS-HSE) questions are on electrotechnical, about 12% of the bank. Try 6 below with full worked answers, then practise the rest in a timed mock.

Practice questions

Pick an answer to see why it's right, why the others are wrong, and the page in the book.

Q1. You have switched off a circuit breaker to work on a circuit, but have no lock. A colleague suggests taping it in the off position. Why is this not enough?

Show answer

Answer: A. Isolation should be locked off with the key removed

  • Switch off the isolating device or remove the fuse.
  • Lock the switch, breaker or enclosure and remove the key.
  • Post a notice warning that someone is working on it.

Tape is not a lock.

Why the others are wrong:

B: colour does not make tape a lock.

C: the time does not change the need to lock off.

D: staying nearby does not secure the isolation.

Memory trick:

Tape is not a lock.

Reg Safe isolation

Q2. Why must you NOT touch a person who is still in contact with a live cable?

Show answer

Answer: C. You could also receive an electric shock

  • Touching someone still in contact with live cables could pass the shock to you.
  • Switch the power off first.

Isolate before you help.

Why the others are wrong:

A: this is not the reason.

B: safety, not evidence, is the reason.

D: the danger is the electricity.

Memory trick:

Touch them, join them.

Reg First aid

Q3. Your firm has two jobs: dead work on an 11 kV switchboard and dead work on a 230 V lighting circuit. Which statement about permits to work is correct?

Show answer

Answer: D. The 11 kV job must have a permit; one can also be used for the 230 V job

  • A permit is always required for work on high-voltage systems.
  • It can also be used for low-voltage systems.
  • It states what has been made safe, how, and what work is to be done, so it is not used for live work.

HV dead work: permit essential. LV dead work: permit optional but useful.

Why the others are wrong:

A: a permit to work should not be used for live working.

B: dead working on high-voltage systems always requires a permit.

C: it is the high-voltage dead work that always needs a permit.

Memory trick:

High voltage? No permit, no work.

Reg Electricity at Work Regulations (permits to work)

Q4. Why should you assume a cable is live until you know otherwise?

Show answer

Answer: C. You cannot tell by looking, hearing or smelling

  • You cannot see, hear or smell electricity.
  • You cannot tell by looking at a cable whether it is live.
  • Always assume cables are live.

It can catch you out without warning.

Why the others are wrong:

A: there is no such rule, you cannot tell by looking.

B: you cannot hear electricity.

D: colour does not tell you whether a cable is live.

Memory trick:

Silent, invisible, odourless: assume live.

Reg Electric shock

Q5. Only 230 V portable tools are available on a building site. Which is correct?

Show answer

Answer: B. Use them with a 30 mA RCD

  • Reduced low voltage (e.g. 110 V centre-point earthed) is strongly preferred on site.
  • Where only 230 V equipment is available, a 30 mA RCD gives additional protection against fatal shock.

If you must use mains, use an RCD.

Why the others are wrong:

A: yellow identifies 110 V, it does not protect a 230 V tool.

C: a larger fuse gives no extra protection against shock.

D: who plugs them in does not add protection.

Memory trick:

Mains on site? RCD in line.

Reg Site supplies

Q6. Accident history shows which kinds of tester have often caused accidents when used to check for voltage?

Show answer

Answer: D. Wrongly set multimeters and makeshift devices

  • Incorrectly set multimeters and makeshift devices have often caused accidents.
  • Use a proprietary test lamp or two-pole voltage detector.
  • Voltage sticks are not advised as the sole means of proving dead.

Use the right tool for proving dead.

Why the others are wrong:

A: these are the recommended devices for proving dead.

B: a proprietary test lamp is a recommended device.

C: these are the type of device that should be used.

Memory trick:

Two poles to prove it's dead.

Reg Safe isolation

Want 394 more ECS HS&E questions? Start a free timed mock.

Start a free mock

Full mock, no card needed. Full workouts on the first 5 questions.

Other ECS HS&E topics

Revise this topic