CITB Work at Height: Planning work at height and the hierarchy of control practice questions

Written by Acacio Oliveira, founder of FreeMocks, plumbing and heating engineer (F-Gas registered).

40 of our 200 CITB HS&E Specialist Test: Work at Height (CITB-SPEC-WAH) questions are on planning work at height and the hierarchy of control, about 20% of the bank. Try 6 below with full worked answers, then practise the rest in a timed mock.

Practice questions

Pick an answer to see why it's right, why the others are wrong, and the page in the book.

Q1. The condition of an old industrial roof is in doubt. How should it be surveyed?

Show answer

Answer: B. Remotely from the ground or from a MEWP, not by walking on it

  • Where the condition of an industrial roof is in any way suspect, do not walk on it to conduct a survey.
  • Use a remote inspection from the ground or access from a MEWP or equivalent safe means.

Roof structures can deteriorate so much that they fail suddenly.

Why the others are wrong:

A: walking on a suspect roof is what HSG33 says not to do.

C: purlin lines are not safe to walk on.

D: a harness does not make walking a suspect roof acceptable.

Memory trick:

Doubt the roof? Don't walk the roof.

Find it in the book

HSE HSG33 Health and safety in roof work (5th edition, 2020), page 43

Reg HSE HSG33, para 186

Q2. In HSE's brief guide, what counts as 'short duration' for low-risk ladder tasks?

Show answer

Answer: A. Tasks that take less than 30 minutes

  • Short duration means tasks that take less than 30 minutes.
  • For low-risk, short-duration ladder tasks, competence may mean instruction on safe use (such as how to tie a ladder) and training.

Training often happens on the job rather than in a classroom.

Why the others are wrong:

B: 2 hours is far longer than the figure given.

C: half a day is far longer than the figure given.

D: 5 minutes is much shorter than the figure given.

Memory trick:

Short duration: under half an hour.

Find it in the book

HSE INDG401(rev2) Working at height: A brief guide (2014), page 2

Reg HSE INDG401(rev2), How do you decide if someone is competent?

Q3. How does HSE describe work at height?

Show answer

Answer: D. Work anywhere a fall could cause personal injury

  • Work at height means work in any place where, without precautions, a person could fall a distance liable to cause personal injury.
  • It includes falling through a fragile surface or into an opening in a floor or a hole in the ground.

Getting to and from a place of work at height is also covered.

Why the others are wrong:

A: there is no minimum height in the definition.

B: it includes roofs, fragile surfaces and openings, not just ladders and scaffolds.

C: the definition is not limited by height or by construction sites.

Memory trick:

Could you get hurt falling? Then it's work at height.

Find it in the book

HSE INDG401(rev2) Working at height: A brief guide (2014), page 1

Reg HSE INDG401(rev2), Introduction

Q4. Why should all the equipment needed for safe working be on site before roof work starts?

Show answer

Answer: D. To avoid ad hoc methods and improvised kit

  • Equipment for safe working should be clearly identified and available before work starts.
  • This avoids 'ad hoc' methods and improvised equipment, which often lead to accidents.

Workers should also know what to do if the method has to change.

Why the others are wrong:

A: hire dates are not a safety reason.

B: HSE does not inspect equipment before use.

C: payment is not a safety reason.

Memory trick:

Kit first, climb second.

Find it in the book

HSE HSG33 Health and safety in roof work (5th edition, 2020), page 11

Reg HSE HSG33, para 26

Q5. A steel erector suggests walking along the top flange of a beam to reach a connection. What does HSE guidance say?

Show answer

Answer: C. It is dangerous and must never be done

  • Walking on the top flange of a steel beam is dangerous and must never be undertaken.
  • Where work cannot be done from a MEWP, beam straddling may be allowed for short-duration jobs on I-section beams, with a back-up such as a harness and twin lanyard.

Any harness-based system needs a rescue plan.

Why the others are wrong:

A: there is no distance under which it is allowed.

B: a lanyard does not make walking the top flange acceptable.

D: straddling an I-beam is a different, controlled method; walking it is never allowed.

Memory trick:

Sit astride, never walk the flange.

Find it in the book

HSE HSG150 Health and safety in construction (2006), page 50

Reg HSE HSG150, para 256

Q6. A house builder wants to cut the amount of work at height when installing roof trusses. Which option does HSG33 say greatly reduces it?

Show answer

Answer: B. Assembling the roof on the ground and craning it into place

  • Prefabrication of roof sections, so that completed sections or whole roofs are craned into place, greatly reduces the need for work at height.
  • A safe working platform is still needed around the perimeter to fix the trusses.

Lifting frames or spreader beams may be needed, planned with the truss designer.

Why the others are wrong:

A: working from ladders is low in the hierarchy.

C: walking the wall plate is a fall risk, not a way to reduce it.

D: a longer lanyard increases fall distance and does not reduce work at height.

Memory trick:

Build it low, lift it high.

Find it in the book

HSE HSG33 Health and safety in roof work (5th edition, 2020), page 34

Reg HSE HSG33, para 133

Want 194 more CITB Work at Height questions? Start a free timed mock.

Start a free mock

Full mock, no card needed. Full workouts on the first 5 questions.

Other CITB Work at Height topics

Free official guides for this topic

Our questions are written from these documents. Download them free to revise from the source.

© Crown copyright (HSE). Unchanged copies, reproduced under the Open Government Licence v3.0. FreeMocks is not connected to or endorsed by HSE or the government.

Revise this topic