CITB Highway Works: Signing, lighting and guarding street works practice questions

Written by Acacio Oliveira, founder of FreeMocks, plumbing and heating engineer (F-Gas registered).

40 of our 200 CITB HS&E Specialist Test: Highway Works (CITB-SPEC-HIW) questions are on signing, lighting and guarding street works, about 20% of the bank. Try 6 below with full worked answers, then practise the rest in a timed mock.

Practice questions

Pick an answer to see why it's right, why the others are wrong, and the page in the book.

Q1. In England, individual pedestrian barriers should withstand winds of what speed, blowing from any direction?

Show answer

Answer: D. 8.7 m/s

  • Barriers must withstand Class C (8.7 m/s) winds from any direction, using ballast or cross-bracing if needed.
  • In Scotland, barriers at sites unattended for 24 hours or more need Class B (17.6 m/s).

Wind classes come from BS 8442.

Why the others are wrong:

A: 17.6 m/s (Class B) applies in Scotland for sites unattended 24 hours or more.

B: this is not the wind speed given in the Code.

C: this is not the wind speed given in the Code.

Memory trick:

C for common: 8.7.

Find it in the book

DfT Safety at street works and road works (2013), page 98

Reg Safety at street works CoP (2013), Pedestrian barriers (wind classes)

Q2. A works vehicle carries a mounted 'Keep left' sign. What should be done while driving to and from site?

Show answer

Answer: B. Cover the sign while travelling

  • Vehicle-mounted 'Keep right/left' signs must be covered when travelling to and from the site.
  • Do not simply turn the sign to point up or down.

When working, the sign shows drivers approaching on the same side which way to pass.

Why the others are wrong:

A: the Code says do not simply turn the sign.

C: this gives drivers a false instruction.

D: the sign still gives a false instruction.

Memory trick:

On the move, cover it.

Find it in the book

DfT Safety at street works and road works (2013), page 91

Reg Safety at street works CoP (2013), Vehicle requirements warning

Q3. A sign keeps being blown over by passing lorries. Which is an acceptable way to secure it?

Show answer

Answer: C. Sacks of granular material placed at low level

  • Equipment with built-in weights is recommended, or add sacks of granular material at low level.
  • Never use barrels, kerbstones, spoil or road pins: they are dangerous if struck.

Signs and barriers must stay put against wind and the draught from passing vehicles.

Why the others are wrong:

A: kerbstones become a danger if struck by a vehicle.

B: road pins must not be used to secure signs.

D: spoil must not be used to weight signs.

Memory trick:

Sandbags low, never kerbs or spoil.

Find it in the book

DfT Safety at street works and road works (2013), page 18

Reg Safety at street works CoP (2013), Fixing of signing, lighting and guarding

Q4. When may flashing warning lights be used instead of steady ones?

Show answer

Answer: C. On lit roads with a limit of 40 mph or less

  • Steady warning lights can be used on any road.
  • Flashing lights are permitted only where street lighting is present and lit and the limit is 40 mph or less.

At 50 mph and 60 mph the table shows no flashing option.

Why the others are wrong:

A: flashing lights are only an option on lit roads up to 40 mph.

B: flashing lights are not permitted at 50 mph or more.

D: height limits do not decide whether flashing lights are allowed.

Memory trick:

Flashing only where it's lit and forty or less.

Find it in the book

DfT Safety at street works and road works (2013), page 19

Reg Safety at street works CoP (2013), Cones and warning lights; Warning lights table

Q5. On which roads does the Safety at street works and road works Code of Practice NOT apply?

Show answer

Answer: B. Motorways, and dual carriageways of 50 mph or more

  • The Code covers all highways and roads except motorways and dual carriageways of 50 mph or more.
  • For those roads, refer to Chapter 8 of the Traffic Signs Manual.

The Code applies to both highway authorities and statutory undertakers, but not skips or scaffolding.

Why the others are wrong:

A: these roads are covered by the Code.

C: the Code covers dual carriageways of 40 mph or less.

D: street lighting does not take a road out of the Code.

Memory trick:

Red Book stops at motorways and fast duals.

Find it in the book

DfT Safety at street works and road works (2013), page 5

Reg Safety at street works CoP (2013), Foreword: Purpose

Q6. The 'Road works ahead' sign must be more than 440 yards from the works. In what order should signs be set out?

Show answer

Answer: B. Initial and extra advance signs before the rest

  • When 'Road works ahead' is more than 440 yards (1/4 mile) from the works, or extra signs are needed for poor visibility,
  • set up the initial and additional advance signs first, then move to the site and set out the rest.

Face traffic when setting out, and take particular care crossing the road.

Why the others are wrong:

A: the far advance signs go out first in this case.

C: advance signs must be in place before works start.

D: advance signing is not optional at this distance.

Memory trick:

Far signs first when it's a quarter mile.

Find it in the book

DfT Safety at street works and road works (2013), page 25

Reg Safety at street works CoP (2013), Sequence for setting out signs

Want 194 more CITB Highway Works questions? Start a free timed mock.

Start a free mock

Full mock, no card needed. Full workouts on the first 5 questions.

Other CITB Highway Works topics

Free official guides for this topic

Our questions are written from these documents. Download them free to revise from the source.

© Crown copyright (DfT, HSE). Unchanged copies, reproduced under the Open Government Licence v3.0. FreeMocks is not connected to or endorsed by HSE or the government.

Revise this topic