Abrasive Wheels: Wheel types, markings and speeds practice questions

Written by Acacio Oliveira, founder of FreeMocks, plumbing and heating engineer (F-Gas registered).

20 of our 80 Abrasive Wheels Awareness (ABRASIVE-WHEELS) questions are on wheel types, markings and speeds, about 25% of the bank. Try 6 below with full worked answers, then practise the rest in a timed mock.

Practice questions

Pick an answer to see why it's right, why the others are wrong, and the page in the book.

Q1. Organic bonded wheels for hand-held machines carry a use-by date. How long after manufacture is it?

Show answer

Answer: B. Three years from the date of manufacture

  • All organic bonded wheels for hand-held use bear a use-by date of three years from manufacture.
  • Check the expiry date on the wheel label before fitting.

Out-of-date wheels should not be used.

Why the others are wrong:

A: the use-by period given is three years, not one.

C: five years is too long; the period is three years.

D: the clock starts at manufacture, not first use.

Memory trick:

Three years from the factory, not from first fit.

Find it in the book

HSE HSG17 (3rd edition, 2000), page 8

Reg HSG17, Shelf life, para 15

Q2. A pneumatic grinder's governor fails and the wheel spins at three times its normal speed. Using HSG17's rule on centrifugal force, how much greater is the stress in the wheel?

Show answer

Answer: B. 9 times greater

  • Centrifugal force rises as the square of the speed, not directly.
  • HSG17's example: doubling speed gives four times the stress.
  • Three times the speed: 3 x 3 = 9 times the stress.

This is why overspeeding is one of the main causes of wheel bursts.

Why the others are wrong:

A: stress does not rise directly with speed; it rises with the square of speed.

C: this doubles the speed factor instead of squaring it.

D: this cubes the speed factor; the rule is the square.

The maths

Step 1: Stress rises with the square of speed.
Step 2: Speed factor = 3.
Step 3: 3 squared = 3 x 3 = 9 times the stress.

Memory trick:

Speed up by x, stress up by x squared.

Find it in the book

HSE HSG17 (3rd edition, 2000), page 12

Reg HSG17, Speed, para 27

Q3. In an abrasive wheel specification, what does the grade letter (from A to Z) describe?

Show answer

Answer: A. How firmly the bond holds the abrasive grains

  • Grade is the tenacity with which the bond holds the abrasive grain.
  • The scale runs from A (extremely soft) to Z (extremely hard).

Soft and hard here describe the bond's grip, not the hardness of the abrasive itself.

Why the others are wrong:

B: grain size is given as a number, from 4 (very coarse) to 1200 (very fine).

C: porosity is the structure, shown by a number.

D: maximum speed is marked in m/s and rpm, not by grade letter.

Memory trick:

Grade letters: A is soft, Z holds tight.

Find it in the book

HSE HSG17 (3rd edition, 2000), page 7

Reg HSG17, Abrasive wheel characteristics, para 11(c)

Q4. The correct operating speed of a mounted point depends on three factors. Which are they?

Show answer

Answer: C. Point shape and size, spindle diameter and overhang

  • Correct speed depends on: the shape and dimensions of the point, the diameter of the spindle, and the overhang from the collet.
  • Overhang is the exposed spindle between the collet and the abrasive.

Overspeed can bend the spindle so the point flies off.

Why the others are wrong:

A: grip and air pressure are not among the three factors.

B: these are wheel selection points, not the speed factors.

D: the factors are shape and size, spindle diameter and overhang.

Memory trick:

Shape, shank, stick-out.

Find it in the book

HSE HSG17 (3rd edition, 2000), page 28

Reg HSG17, Mounted wheels and points, para 90

Q5. What does the structure number in a wheel's specification tell you?

Show answer

Answer: B. The level of porosity: a higher number means more porous

  • Structure means the level of porosity in the wheel.
  • The higher the number, the greater the porosity.

The wrong structure for the job can lead to loading.

Why the others are wrong:

A: bond hold is the grade, shown by a letter A to Z.

C: grain size is a separate number from 4 to 1200.

D: the shape is given by the ISO type number.

Memory trick:

Structure counts the holes.

Find it in the book

HSE HSG17 (3rd edition, 2000), page 7

Reg HSG17, Abrasive wheel characteristics, para 11(d)

Q6. A wheel has coloured stripes across its label. What do these stripes tell you?

Show answer

Answer: A. Its maximum speed is 50 m/s or more

  • For maximum speeds of 50 m/s and above, colour-coded stripes appear on the wheel.
  • The maximum speed is also marked in m/s and rpm on wheels over 80 mm.

Always compare the marked speed with the machine spindle speed before fitting.

Why the others are wrong:

B: reinforcement is not shown by speed stripes.

C: the use-by date is printed as an expiry date.

D: wet grinding limits are shown by restriction codes.

Memory trick:

Stripes mean speed: 50 and up.

Find it in the book

HSE HSG17 (3rd edition, 2000), page 7

Reg HSG17, Maximum permissible speed, para 13

Want 74 more Abrasive Wheels questions? Start a free timed mock.

Start a free mock

Full mock, no card needed. Full workouts on the first 5 questions.

Other Abrasive Wheels topics

Free official guides for this topic

Our questions are written from these documents. Download them free to revise from the source.

© Crown copyright (HSE). Unchanged copies, reproduced under the Open Government Licence v3.0. FreeMocks is not connected to or endorsed by HSE or the government.

Revise this topic