Abrasive Wheels: The law, training and competence practice questions

Written by Acacio Oliveira, founder of FreeMocks, plumbing and heating engineer (F-Gas registered).

20 of our 80 Abrasive Wheels Awareness (ABRASIVE-WHEELS) questions are on the law, training and competence, about 25% of the bank. Try 6 below with full worked answers, then practise the rest in a timed mock.

Practice questions

Pick an answer to see why it's right, why the others are wrong, and the page in the book.

Q1. Which regulations now set the main legal duties for the selection and use of abrasive wheels at work?

Show answer

Answer: B. The Provision and Use of Work Equipment Regulations 1998

  • PUWER 98 covers the selection and use of work equipment in general, including abrasive wheels.
  • It revoked the remaining provisions of the Abrasive Wheels Regulations 1970.

HSG17 explains how the general PUWER duties apply to abrasive wheels.

Why the others are wrong:

A: PUWER 98 revoked the remaining provisions of the 1970 Regulations, so they no longer apply.

C: these deal with machinery as supplied by makers, not the selection and use of work equipment.

D: these cover noise, a hazard HSG17 leaves to other regulations.

Memory trick:

Wheels are work equipment, so PUWER rules.

Find it in the book

HSE HSG17 (3rd edition, 2000), page 5

Reg Provision and Use of Work Equipment Regulations 1998 (HSG17, Preface)

Q2. A site manager organises who changes grinding wheels but never grinds or mounts wheels personally. Does PUWER's information and training duty cover them?

Show answer

Answer: A. Yes, people managing abrasive wheel work must be trained too

  • PUWER 98 requires employees, including those using, mounting and managing the operation of abrasive wheels, to be fully informed and properly trained.
  • It also requires equipment to be suitable and properly maintained.

Managers need enough knowledge to set and check safe systems.

Why the others are wrong:

B: PUWER covers those using, mounting and managing abrasive wheels.

C: managers are included alongside users and mounters.

D: no card is mentioned; managing the work brings them in.

Memory trick:

Use it, mount it or manage it: train for it.

Find it in the book

HSE HSG17 (3rd edition, 2000), page 5

Reg HSG17, Introduction, para 3

Q3. Your employer is drawing up an abrasive wheels training programme. Which topic does HSG17 list as one the training should cover as a minimum?

Show answer

Answer: D. How wheels are marked with type, size and maximum speed

  • Paragraph 6 lists the minimum training content, including methods of marking wheels with their type, size and maximum operating speed.
  • Other items include hazards, storage and handling, inspection, components, assembly, dressing, work rest adjustment and PPE.

Knowing the markings lets a mounter check the wheel suits the machine.

Why the others are wrong:

A: balancing with sliding weights is a precision grinding technique, not on the minimum training list.

B: governors should be repaired or adjusted only by a competent person, not covered by basic training.

C: the machine maker's advice should be sought before re-truing cambered flanges.

Memory trick:

Read the wheel before you fit the wheel.

Find it in the book

HSE HSG17 (3rd edition, 2000), page 6

Reg HSG17, Training, para 6(b)

Q4. To which workplaces does PUWER 98 apply?

Show answer

Answer: A. All work situations covered by the HSW Act 1974

  • PUWER 98 applies to all workplaces and work situations subject to the Health and Safety at Work etc Act 1974.
  • Abrasive wheels in foundries, engineering and construction are all covered.

The duty follows the work, not the type of premises.

Why the others are wrong:

B: PUWER covers all workplaces under the HSW Act, not just factories.

C: PUWER is not limited to construction.

D: no employee threshold applies to PUWER.

Memory trick:

Wherever the HSW Act goes, PUWER goes.

Find it in the book

HSE HSG17 (3rd edition, 2000), page 5

Reg Provision and Use of Work Equipment Regulations 1998 (HSG17, Preface)

Q5. HSG17's training list includes the proper method of dressing a wheel. What does dressing mean?

Show answer

Answer: B. Removing dulled abrasive or material from the cutting face

  • Dressing means removing dulled abrasive or other material from the cutting surface.
  • It can also mean removing material to correct uneven wear of the wheel.

Frequent light dressing keeps the wheel cutting without extra pressure.

Why the others are wrong:

A: that is part of mounting, not dressing.

C: that is guarding, not dressing.

D: that is the ring test, part of inspection.

Memory trick:

Dressing freshens the face.

Find it in the book

HSE HSG17 (3rd edition, 2000), page 6

Reg HSG17, Training, para 6(g)

Q6. A manager wants further information about abrasive wheel training courses. Which organisation does HSG17 point to?

Show answer

Answer: A. The British Abrasives Federation

  • Training courses are offered by many organisations, usually with a certificate of attendance.
  • Further information can be obtained from the British Abrasives Federation.

The Federation helped prepare the revised guidance.

Why the others are wrong:

B: BSI publishes standards such as BS EN 12413, not training information.

C: fire services are not named as a source of training information.

D: HSG17 names the British Abrasives Federation for course information.

Memory trick:

Abrasives questions? Abrasives Federation.

Find it in the book

HSE HSG17 (3rd edition, 2000), page 6

Reg HSG17, Training, para 7

Want 74 more Abrasive Wheels questions? Start a free timed mock.

Start a free mock

Full mock, no card needed. Full workouts on the first 5 questions.

Other Abrasive Wheels topics

Free official guides for this topic

Our questions are written from these documents. Download them free to revise from the source.

© Crown copyright (HSE). Unchanged copies, reproduced under the Open Government Licence v3.0. FreeMocks is not connected to or endorsed by HSE or the government.

Revise this topic