Abrasive Wheels: Mounting, guards and inspection practice questions

Written by Acacio Oliveira, founder of FreeMocks, plumbing and heating engineer (F-Gas registered).

20 of our 80 Abrasive Wheels Awareness (ABRASIVE-WHEELS) questions are on mounting, guards and inspection, about 25% of the bank. Try 6 below with full worked answers, then practise the rest in a timed mock.

Practice questions

Pick an answer to see why it's right, why the others are wrong, and the page in the book.

Q1. Which describes a correctly fitted blotter?

Show answer

Answer: C. Slightly larger than the flange and free from wrinkles

  • Blotters should be slightly larger than the flanges and free from wrinkles.
  • Remove any old blotter pieces or loose grains first, or high spots cause local stress.

They should be an easy fit on the spindle.

Why the others are wrong:

A: blotters should be slightly larger than the flanges.

B: each blotter must be flat and free from wrinkles.

D: a blotter can act as a label, but a label cannot act as a blotter.

Memory trick:

Bigger than the flange, flat as a page.

Find it in the book

HSE HSG17 (3rd edition, 2000), pages 19 and 28

Reg HSG17, Blotters, para 55; para 96

Q2. How should thin, organic bonded cutting-off wheels be stored to stop them warping?

Show answer

Answer: A. Flat on a rigid level surface, away from heat and damp

  • Thin organic cutting-off wheels should be laid flat on a horizontal surface of steel or similar rigid material.
  • Keep them away from excessive heat and moisture, with no blotters between stacked wheels.

A warped wheel should not be used.

Why the others are wrong:

B: thin cutting-off wheels should be laid flat to prevent warping.

C: hanging does not keep them flat; lay them on a rigid surface.

D: blotters or packing should not be placed between stacked thin wheels.

Memory trick:

Thin wheels lie flat.

Find it in the book

HSE HSG17 (3rd edition, 2000), page 11

Reg HSG17, Storage, para 21

Q3. The machine maker gives no tightening torque for the single central nut holding a wheel. How should it be tightened?

Show answer

Answer: C. By hand pressure on a spanner, just enough to drive the wheel

  • Tighten the nut only enough for the flanges to drive the wheel and prevent slip.
  • Use a torque wrench if a torque is recommended; otherwise hand pressure on a spanner only.

Extensions and hammers apply excessive clamping pressure.

Why the others are wrong:

A: excess clamping from an extension can damage the wheel.

B: hammering can damage the wheel.

D: over-tightening sets up crushing stress that may cause breakage.

Memory trick:

Snug by hand, no bar, no hammer.

Find it in the book

HSE HSG17 (3rd edition, 2000), page 20

Reg HSG17, Securing the wheel, paras 60 to 62

Q4. A fitter has a cutting-off wheel with a bore too large for an angle grinder spindle and plans to fit a plastic bush to reduce it. What does HSG17 say?

Show answer

Answer: A. Bushes are not recommended on portable hand-held machines

  • Bushes reduce a wheel's hole size but are not recommended for wheels on portable grinding machines.
  • This includes using a bush to reduce the bore of a cutting-off wheel on a hand-held machine.

Use a wheel with a hole that suits the spindle.

Why the others are wrong:

B: a bush should not project beyond the wheel and blotters.

C: bushes may be plastic or metal; neither is recommended on portable machines.

D: narrow bushes can slide out into the flange recess and work loose.

Memory trick:

Wrong bore on a hand tool? Wrong wheel.

Find it in the book

HSE HSG17 (3rd edition, 2000), pages 19 and 37

Reg HSG17, Wheel bushes, para 57; Bushes, para 129

Q5. During a ring test, a wheel gives a dull, dead sound. What should you do?

Show answer

Answer: B. Do not use it, as it may be cracked

  • If a wheel sounds dead, for example due to cracking, it should not be used.
  • Make sure the wheel is dry and free of sawdust first, as these deaden the sound.

If in doubt, compare with wheels of the same lot and tell the manufacturer.

Why the others are wrong:

A: a dead-sounding wheel should not be used at any speed.

C: a trial run does not make a cracked wheel safe.

D: cracks may not be visible; the dead sound is the warning.

Memory trick:

Dead sound, dead wheel.

Find it in the book

HSE HSG17 (3rd edition, 2000), page 9

Reg HSG17, Examination, para 18

Q6. What is the main purpose of the blotters fitted between a wheel and its flanges?

Show answer

Answer: B. To spread the clamping force of the flanges evenly

  • Blotters are compressible, usually card 0.2 mm to 1.0 mm thick.
  • Their main job is to distribute the clamping force evenly; they also help prevent slipping and reduce flange wear.

They should be slightly larger than the flanges and free from wrinkles.

Why the others are wrong:

A: a blotter can serve as a label, but a label cannot act as a blotter.

C: that is the job of a bush, not a blotter.

D: blotters are about even clamping, not spark protection.

Memory trick:

Blotters spread the squeeze.

Find it in the book

HSE HSG17 (3rd edition, 2000), page 19

Reg HSG17, Blotters, para 55

Want 74 more Abrasive Wheels questions? Start a free timed mock.

Start a free mock

Full mock, no card needed. Full workouts on the first 5 questions.

Other Abrasive Wheels topics

Free official guides for this topic

Our questions are written from these documents. Download them free to revise from the source.

© Crown copyright (HSE). Unchanged copies, reproduced under the Open Government Licence v3.0. FreeMocks is not connected to or endorsed by HSE or the government.

Revise this topic