Abrasive Wheels: Safe use and hazards practice questions

Written by Acacio Oliveira, founder of FreeMocks, plumbing and heating engineer (F-Gas registered).

20 of our 80 Abrasive Wheels Awareness (ABRASIVE-WHEELS) questions are on safe use and hazards, about 25% of the bank. Try 6 below with full worked answers, then practise the rest in a timed mock.

Practice questions

Pick an answer to see why it's right, why the others are wrong, and the page in the book.

Q1. An electric angle grinder is needed on a construction site where only a 240-volt supply is available. What does HSG17 say?

Show answer

Answer: C. Protect it with an RCD, though 110 volts is preferred

  • The preferred voltage for portable grinders on construction sites is 110 volts.
  • If 240 volts has to be used, the supply should be protected by an RCD.

Electrical safety matters as much as wheel safety on electric grinders.

Why the others are wrong:

A: 110 volts is the preferred voltage on construction sites.

B: an RCD should protect a 240-volt supply to a portable machine.

D: lead length is not a protective measure.

Memory trick:

Site tools: 110, or 240 with an RCD.

Find it in the book

HSE HSG17 (3rd edition, 2000), page 34

Reg HSG17, Electric grinding machines, para 115

Q2. You are cutting a steel bar with an abrasive cutting-off wheel. How should the bar be held?

Show answer

Answer: B. Rigidly supported and firmly clamped

  • The workpiece should be rigidly supported and firmly clamped.
  • Apply pressure evenly and avoid twisting or side pressure on the wheel.

Lack of rigidity in the wheel or work can lead to breakage.

Why the others are wrong:

A: lack of rigidity can lead to wheel breakage; clamp it.

C: the work should be rigidly supported, not loose.

D: the workpiece should be rigidly supported and clamped.

Memory trick:

Clamp the job, not your grip.

Find it in the book

HSE HSG17 (3rd edition, 2000), page 41

Reg HSG17, Summary of operating precautions, para 155

Q3. What does HSG17 say about the floor right around a fixed grinding machine?

Show answer

Answer: A. Keep it in good condition and free from obstruction

  • The floor around fixed grinders should be in good condition and free from obstruction.
  • Splash guards should be used where needed to stop it becoming slippery.

A slip at a grinder can put hands onto the wheel.

Why the others are wrong:

B: splash guards should be used to stop the floor becoming slippery.

C: a wet floor is a slip hazard next to a running wheel.

D: the floor should be free from obstruction.

Memory trick:

Clear floor, firm footing.

Find it in the book

HSE HSG17 (3rd edition, 2000), page 40

Reg HSG17, Summary of operating precautions, para 143

Q4. A wheel bursts on a bench grinder. The guard held and nobody was hurt. What does HSG17 say should happen next?

Show answer

Answer: C. Investigate carefully to find the cause and stop a repeat

  • Every breakage of a wheel should be followed by careful investigation.
  • The aim is to find the cause and take suitable action to prevent a recurrence.

Causes include bad storage, wrong wheel selection, poor mounting, overspeed and machine defects.

Why the others are wrong:

A: refitting without finding the cause risks the same failure again.

B: the cause must be found first; the wrong wheel choice can itself cause breakage.

D: every breakage should be investigated, even when no one was hurt.

Memory trick:

Wheel burst? Find out why first.

Find it in the book

HSE HSG17 (3rd edition, 2000), page 9

Reg HSG17, Wheel breakage, para 17

Q5. A grinding wheel has glazed. A colleague suggests knocking it clean with a chipping hammer. What is right?

Show answer

Answer: A. Use a proper, well-supported dresser, never a hammer

  • Haphazard dressing, such as a chipping hammer or striking the work against the wheel, should be forbidden.
  • Hand dressers should be properly supported; revolving cutter dressers anchored by their lugs.

Frequent light dressings are better than occasional severe ones.

Why the others are wrong:

B: striking the work against the wheel is a forbidden method.

C: haphazard methods such as a chipping hammer should be forbidden.

D: glazing tempts operators to press harder, raising the risk of breakage.

Memory trick:

Dress with a dresser, not a hammer.

Find it in the book

HSE HSG17 (3rd edition, 2000), page 37

Reg HSG17, Truing and dressing, para 130

Q6. Where should the start and stop controls on a grinding machine be placed?

Show answer

Answer: A. Clearly marked, in a safe place within the operator's reach

  • Start and stop controls should be clearly visible and marked, in a safe position and within easy reach.
  • On portable machines, the control should be placed so there is no risk of accidental starting when put down flat.

The operator must be able to stop the wheel quickly.

Why the others are wrong:

B: controls must be within easy reach of the operator.

C: the operator needs them close at hand to stop quickly.

D: they must be clearly visible, marked and within easy reach.

Memory trick:

Stop button: seen, signed, in reach.

Find it in the book

HSE HSG17 (3rd edition, 2000), page 16

Reg HSG17, Stopping devices, para 43

Want 74 more Abrasive Wheels questions? Start a free timed mock.

Start a free mock

Full mock, no card needed. Full workouts on the first 5 questions.

Other Abrasive Wheels topics

Free official guides for this topic

Our questions are written from these documents. Download them free to revise from the source.

© Crown copyright (HSE). Unchanged copies, reproduced under the Open Government Licence v3.0. FreeMocks is not connected to or endorsed by HSE or the government.

Revise this topic