ELEC3/008: Lighting, heating, electronics and earthing practice questions

Written by Acacio Oliveira, founder of FreeMocks, plumbing and heating engineer (F-Gas registered).

130 of our 270 Principles of Electrical Science (ELEC3-008) questions are on lighting, heating, electronics and earthing, about 48% of the bank. Try 6 below with full worked answers, then practise the rest in a timed mock.

Regulations that come up most

The regulation groups our lighting, heating, electronics and earthing questions test most often. Know where these are in your book before the exam.

  • 559.9 · 3 questions
  • 411.3 · 1 questions
  • 537.3 · 1 questions
  • 559.4 · 1 questions
  • 701.753 · 1 questions

Practice questions

Pick an answer to see why it's right, why the others are wrong, and the page in the book.

Q1. An LED indicator (2 V, 10 mA) is to be powered from a 24 V d.c. control supply. What series resistance is needed?

Show answer

Answer: B. 2.2 kΩ

  • Resistor voltage = 24 − 2 = 22 V
  • R = 22 ÷ 0.01 = 2200 Ω = 2.2 kΩ

Without the resistor the LED would be destroyed.

Why the others are wrong:

A: ignores the 2 V dropped across the LED.

C: uses 100 mA rather than 10 mA.

D: uses 1 mA rather than 10 mA.

The maths

R = (24 − 2) ÷ 0.01
= 22 ÷ 0.01 = 2200 Ω = 2.2 kΩ

Memory trick:

(Supply − 2) ÷ 0.01.

Find it in the book

Linsley, Electrical Installation Work Level 3 (EAL Edition), page 386

Reg ELEC3/008 AC2.1 LED

Q2. What is the maximum noise level permitted for chokes made to BS EN 60598, as stated in the textbook?

Show answer

Answer: C. 30 dB

  • Constant reversal of magnetism in the laminated core makes chokes vibrate
  • BS EN 60598 chokes have a maximum noise level of 30 dB, about a quiet watch at 1 m

Rigid fixing keeps the noise down.

Why the others are wrong:

A: this is the level of normal conversation and far too loud for a choke.

B: this is a typical noise at work action level, not a choke limit.

D: this is lower than the stated limit.

Memory trick:

Choke limit: 30, a whisper.

Find it in the book

Linsley, Electrical Installation Work Level 3 (EAL Edition), page 450

Reg AC 4.3

Q3. Which quantity measures the flow of light radiated from a source, and what is its unit?

Show answer

Answer: B. Luminous flux, measured in lumens

  • Luminous flux (symbol F) is the flow of light from a source
  • Its unit is the lumen: the flux emitted within a unit solid angle from a 1 cd point source

Flux is the quantity used in the lumen method.

Why the others are wrong:

A: illuminance is light falling on a surface, measured in lux.

C: luminance is the brightness of a surface, not flow from a source.

D: intensity is measured in candela.

Memory trick:

Flux flows: lumens leave the lamp.

Find it in the book

Linsley, Electrical Installation Work Level 3 (EAL Edition), page 432

Reg AC 4.1

Q4. When sizing the cable for a single storage radiator, what current demand does the textbook say to assume?

Show answer

Answer: C. 3.4 kW at each point

  • For a single storage radiator, assume a current demand of 3.4 kW at each point

This figure is used for cable sizing.

Why the others are wrong:

A: this is lower than the value stated.

B: this is nearer the lower end of a central ducted unit.

D: this is the multiplier for discharge lighting.

Memory trick:

Storage radiator: 3.4 kW per point.

Find it in the book

Linsley, Electrical Installation Work Level 3 (EAL Edition), page 470

Reg AC 7.1

Q5. Lamps with a rated life of 6000 hours are lit for 60 hours each week. After how many weeks should they be group replaced?

Show answer

Answer: D. 100 weeks

  • Interval = rated life / hours used per week
  • 6000 / 60 = 100 weeks

The interval comes from the manufacturer's rated life and the hours per week the lamps are lit.

Why the others are wrong:

A: this is out by a factor of ten.

B: this multiplies by 60 then divides by 1000.

C: this divides by 52, the weeks in a year, instead of the hours per week.

The maths

6000 / 60 = 100 weeks

Memory trick:

Life hours ÷ hours per week = weeks.

Find it in the book

Linsley, Electrical Installation Work Level 3 (EAL Edition), page 452

Reg AC 4.3

Q6. Why must a low-pressure sodium (SOX) lamp be operated horizontally, or close to horizontal?

Show answer

Answer: A. So the condensing sodium spreads evenly around the U-tube

  • The SOX lamp has a U-shaped arc tube containing sodium and neon
  • It must be operated horizontally (or within about 20°) so that, when switched off, the condensing sodium is evenly distributed around the U-tube

It takes several minutes to reach full brightness, changing from red to bright yellow.

Why the others are wrong:

B: the neon fills the whole tube and is not affected by position.

C: the control gear is separate and its cooling does not depend on lamp position.

D: burning position is set by the lamp's operation, not its light distribution.

Memory trick:

SOX lies flat so its sodium spreads out like butter.

Find it in the book

Linsley, Electrical Installation Work Level 3 (EAL Edition), page 444

Reg Low-pressure sodium lamps

Want 264 more ELEC3/008 questions? Start a free timed mock.

Start a free mock

Full mock, no card needed. Full workouts on the first 5 questions.

Other ELEC3/008 topics

Revise this topic